| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
A subsequest revision will set them again as needed,
per coreboot target.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
See:
https://codeberg.org/libreboot/lbmk/issues/216
Almost all users will be OK running GRUB, but a
minority of users have experienced a fatal error
pertaining to grub_free() or grub_realloc() (as
my investigation of GRUB sources reveal when grepping
the error reported in the link above).
We don't yet know what the bug is, only that the
error occurs, leading to an effective brick if the
user has GRUB as their primary payload.
So far, it has only been reported on some Intel
SandyBridge-based Dell Latitudes in Libreboot, but
we can't be too sure.
The user reported that memtest86+ passes just fine,
and SeaBIOS works; BIOS GRUB also works, which means
that the bug is likely only in an area of GRUB that
runs specifically on the coreboot payload, so it's
probably a driver in GRUB when running on the metal
rather than BIOS/UEFI.
The build system supports a configuration whereby
SeaBIOS is the primary payload, but GRUB is available
in the SeaBIOS boot select menu, and an additional
configuration is available where GRUB is what SeaBIOS
executes first (while still providing boot select);
both of these are now the *only* configurations
available, on all x86 targets except QEMU.
The QEMU target is fine because if the bug occurs there,
you can just close QEMU and try a different image.
Even after this bug is later identified and fixed,
the GRUB source code is vastly over-engineered and there
are likely many more such bugs. SeaBIOS is a reliable
payload; the code is small and robust. Remember always:
Code
equals
bugs
Therefore, this configuration change is likely going
to be permanent. This will apply in the next release.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
The E6400 uses a 100 MHz reference clock on DPLL_REF_SSCLK, whereas
libgfxinit assumed that the reference was always 96 MHz. The frequency
difference caused by a 100 MHz reference with PLL config values
calculated assuming a 96 MHz reference were not significant enough to
cause noticable issues with the more common 1280 x 800 panels, but are
enough to matter for the 1440 x 900 panels which use a higher pixel
clock. This only affected the pre-OS graphics environment provided by
libgfxinit, as Linux drivers would determine the reference clock
frequency based on data in the VBT.
Fix this by making the reference clock frequency in libgfxinit
configurable for GM45 based on a new coreboot Kconfig, which is set to
100 MHz for the E6400.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
the release variable is all we need, turning a target on
or off for a given release.
the status checks were prone to bugs, and unnecessary; it
also broke certain benchmark scripts.
it's better to keep the lbmk logic simpler. board status
will be moved to the documentation instead.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
working s3 means i'm happy to mark it as being stable.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
also warn about issues, in a warn.txt file for each.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
export LBMK_VERSION_TYPE=x
x can be: stable, unstable
in target.cfg files, specify:
status=x
x can be: stable, unstable, broken, untested
if unset, lbmk defaults to "unknown"
if LBMK_VERSION_TYPE is set, no confirmation is asked
if the given target matches what's set (but what's set
in that environmental variable can only be stable or
unstable)
if LBMK_RELEASE="y", no confirmation is asked, unless
the target is something other than stable/unstable
"unstable" means it works, but has a few non-breaking
bugs, e.g. broken s3 on dell e6400
whereas, if raminit regularly fails or it is so absolutely
unreliable as to be unusable, then the board should be
declared "broken"
untested means: it has not been tested
With this change, it should now be easier to track whether
a given board is tested, in preparation for releases. When
working on trees/boards, status can be set for targets.
Also: in the board directory, you can add a "warn.txt" file
which will display a message. For example, if a board has a
particular quirk to watch out for, write that there. The message
will be printed during the build process, to stdout.
If status is anything *other* than stable, or it is unstable
but LBMK_VERSION_TYPE is not set to "unstable", and not building
a release, a confirmation is passed.
If the board is not specified as stable or unstable, during
a release build, the build is skipped and the ROM is not
provided in that release; this is in *addition* to
release="n" or release="y" that can be set in target.cfg,
which will skip the release build for that target if "n"
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
re-use the same patches, and drop the same patches.
this tree uses hell's special ddr2 fix, which we apply
for the dell latitude e6400.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
arch no longer needs to be set, on multi-tree projects,
and it has been renamed to xarch
the new behaviour is: if xarch is set, treat it as a
list of crossgcc targets and go through the list. set
the first one as the target, for what lbmk builds, but
build all of the defined crossgccc targets
crossgcc_ada is now xlang, and defines which languages
to build, rather than whether to build gcc-gnat
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the e6400_4mb target has libgfxinit and (if seabios) vgarom
initialisation, but has issues on the nvidia model, even when
using nomodeset. with this target, e6400nvidia_4mb, only
the vgarom initialisation is used, libgfxinit is disabled.
on nvidia models, this one should work a little bit better.
specifically: nouveau crashes on this machine, with libreboot
installed, but you can use nomodeset. however, when libgfxinit
is also enabled, nomodeset no longer works properly.
so this target disables all video initialisation in coreboot.
only seabios will initialise anything video-related, by
executing the vga option rom.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
