| Age | Commit message (Collapse) | Author |
|---|
|
the x220 edp patch invalidated lots of configs, so
i did: ./update trees -u coreboot
this is the resulting patch
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
only call crossgcc for coreboot and u-boot, but use
hostcc for everything else. simplify the checking of
which architecture to compile for. "arch" in target.cfg
files has been modified, to allow further simplification.
without this patch, the logic currently only *barely* avoids
using crossgcc on things like utils, and only works in practise
because, in practise, lbmk only works on x86_64 anyway.
the new logic, as per this patch, is simpler and more robust.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
(#170) from nic3-14159/lbmk:xx30_16_ifd_fix into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/170
|
|
into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/169
|
|
The component 1 and 2 densities were still set to 8 MiB and 4 MiB
respectively, which is incorrect for 16 MiB only configurations.
Change the component 1 density to 16 MiB so that the address space
gets properly mapped to SPI 1. In addition, change the number of
components field (byte 0x15) to 0x00 to indicate 1 flash chip.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Inside the BIOS update, there's 68SCE and 68SCF variants.
Based on Qubes HCL and browsing linux-hardware.org, these are
Probook 6360b and Elitebook 8460p respectively.
I checked the KBC1126 EC Firmwares within the update file, both
use the exact same firmware images. Following-up will be a very
similar but untested port for 6360b.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
do not use a subshell. use git -C instead.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
remove unnecessary "continue" command. it's written
at the end of a for loop, where it'll continue anyway
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the code wasn't very clear. make it clearer.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
this part of the code *must* return. the for loop
afterwards must not be permitted to execute.
it's unlikely that this would ever occur, unless
perhaps the user is using a very buggy sh.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
there are special menuentries just for loading
configs, without handling luks, lvm and whatnot.
it's intended for users of cd/dvd drives. well,
now we support both extlinux and grub, with this patch.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
many modern distros use grub in their installer images,
so scan for grub.cfg first.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
isolinux/syslinux/extlinux config files should all work,
using the syslinux parser function in grub
the current behaviour is to only search for grub.cfg,
so extlinux users can't use the default libreboot setup.
with this change, their systems should hopefully work.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the so-called EFI System Partition (ESP) is used
on many UEFI-based setups. some users may be
migrating to libreboot, so let's support it.
on BIOS setups, it would be e.g.
/boot/syslinux/syslinux.conf
on UEFI setups, it would be e.g.
/boot/EFI/syslinux/syslinux.conf
additionally, support scanning for extlinux.conf
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the fallback code in the main menuentry is
potentially unsafe, depending on user config.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
lvm/* is slow to resolve in grub, on some machines,
because grub enumeration is very slow in general.
however, many people will install distros with any
number of lvm configurations, so we should try to
support them.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
This reverts commit 20389655e42e62ebf6d96dd106c91fbe74282557.
If the user actually has encryption, but has /boot unencrypted,
this will considerably slow down the boot, so the patch has
been reverted.
The patch was originally meant to favour encrypted /boot
setups, but the old behaviour also still works there.
|
|
from nic3-14159/lbmk:dell-flash-unlock-updates into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/168
|
|
when the user sets up an encrypted machine, grub.cfg
defaults to non-encrypted setups if found, first
this patch reverses the order, deferring to
non-encrypted installations only when encrypted ones
are unavailable
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
These systems have a report that the unlock utility does not work.
Until there are multiple reports of failed unlocks and a technical
determination of why it doesn't work, they will not be listed as
explicitly unsupported.
|
|
|
|
As this utility requires access to /dev/mem, the default protections of
Linux and OpenBSD must be relaxed to allow this. Make a note of this in
the instructions.
|
|
The old Open Security Training site had a course called Advanced x86:
BIOS and SMM Internals, which had a set of slides outlining the method
to supress SMIs by changing the GBL_SMI_EN bit. Add a reference to it as
this is where I originally learned of this method.
|
|
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/165
|
|
semigel/lbmk:semigel-btrfs-subvol-patch-1 into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/167
|
|
grub.cfg: add BTRFS subvol support
|
|
|
|
|
|
|
|
all it did was set -v in the shell, which doesn't yield
very useful results. this is a relic of very old design
in the libreboot build system, that is no longer needed.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
lbmk didn't quote certain arguments in commands, or
used ! -z instead of -n, things like that. simple fixes.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
xfonts-unifont' (#163) from Riku_V/lbmk:debgrub into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/163
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
most of these are probably redundant, and will never
be called, but lbmk needs to be as safe as possible
under fault conditions. fail early, fail hard.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
update/trees wasn't correctly returning non-zero status,
even though it was printing an error message, when git-am
failed. this is due to the way subshells work, and it was
overlooked in previous auditing.
additionally: don't directly copy trees to the destination,
instead patch/reset first, then copy only under normal
condition, just as with single-tree projects.
when running build/roms, the script would continue after
a bad git-am, without exit. this patch fixes it in the
most paranoid way possible. i'm now fairly confident that
lbmk will fail gracefully and efficiently, under error
conditions. this should prevent bad image builds.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Riku_V/lbmk:fixvoid into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/161
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
Riku_V/lbmk:fixvoid into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/160
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
Riku_V/lbmk:fivoid into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/159
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
