| Age | Commit message (Collapse) | Author |
|---|
|
nic3-14159/lbmk:autoport-fork into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/195
|
|
This is a copy of coreboot's autoport utility, with a patch applied to
support Haswell/Lynx Point platforms. That patch is currently in review
on coreboot's Gerrit.
https://review.coreboot.org/c/coreboot/+/30890
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
|
|
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/192
|
|
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Needed to make graphics cards work. Turn it on if you're using
only the Intel GPU.
With IOMMU *enabled*, graphics cards do not work reliably at all.
The cause still needs to be investigated, but the symptoms are
graphical corruption on the screen, and Xorg usually crashes.
In some cases (on some cards), TTYs can still be used; the payload
can still be used reliably, on a graphics card, but Xorg fails to
work properly.
This could be a bug in Linux drivers, instead of anything that
coreboot does (not yet tested in factory BIOS).
Leaving it off by default will ensure reliable operation on all
setups, whether an iGPU or dGPU is used.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
It is now possible to disable the IOMMU on Haswell
boards, by doing this on your ROM image:
./nvramtool -C libreboot.rom -w iommu=Disable
To enable it again, do this:
./nvramtool -C libreboot.rom -w iommu=Enable
If not specified, the default behaviour is *on*.
A follow-up patch will turn IOMMU *off* by default,
on Dell OptiPlex 9020 SFF/MT, by setting it as such
in cmos.default. This is to make graphics cards work
properly to work around a bug when it's turned on.
Leaving the IOMMU enabled is recommended, if it works.
It works in most cases, including on 9020 SFF/MT when
using the Intel GPU without a graphics card inserted.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the current entry is fine, but it would then not support
other configs of different flash sizes, unless they are
explicitly defined.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
makes graphics cards work
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
nic3-14159/lbmk:add-dell-ivb-ifd-nogbe into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/188
|
|
This is required by the Latitude E5530, which uses a Broadcom NIC
instead of the Intel ones. The original port was missing this file.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Riku_V/lbmk:hp8560w into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/187
|
|
Iru Cai's port from Gerrit:
https://review.coreboot.org/c/coreboot/+/39398
Now with the proper MXM structure, which removes the 30 second POST
delay. Tested with i7-2670QM, Quadro 2000M and 32GB RAM.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
this merges the fix from:
https://codeberg.org/libreboot/pico-serprog/pulls/1
however, PRs are not to be sent there. riku merged it in
his repository, and i pulled it in the mirror hosted
on libreboot codeberg
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
nic3-14159/lbmk:latitude-ports into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/184
|
|
Tested by Minimum_Baseball_629 on Reddit
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
The OptiPlex 9020/7020 port was merged first and was numbered 31.
Increment the numbering of the Latitude patches to reflect this.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
i enabled it but it's buggy according to comments on gerrit.
disable for now. dgpu didn't work anyway, even with it turned
off, when i had this tested.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
keep dell9020mt_12mb
dell9020mtvga_12mb doesn't actually work (was tried for
running a graphics card on its own, with no igpu init)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Riku_V/lbmk:master into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/185
|
|
should fix https://codeberg.org/libreboot/lbmk/issues/182
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
this was done automatically by running:
./update trees -u coreboot
this has to be done when adding patches for now board ports,
because of the way lbmk and also coreboot's build systems work.
the configs just have to be re-generated to include a line
that says the entry for the newly added boards isn't set. look
at the diff of this commit as an example.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
nic3-14159/lbmk:latitude-ports into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/183
|
|
./update release -m u-boot
if someone just wants to make u-boot, they can
use this and it tars up all the trees.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
on a dgpu setup, igpu was still in use, when tested
by a user. do separate roms that don't enable anything
vga in coreboot, relying instead only on seabios to
execute a vga rom. these roms will only work if you
have a graphics card.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
Specifically the MT versions. The SFF versions will
be added separately, in a later commit.
See: https://review.coreboot.org/c/coreboot/+/55232
This patch has been added, from patchset 31. It still
has some unresolved issues, on that patchset, but
it should boot. See commit message there.
Of note: I've enabled PCI REBAR, though it's unknown
whether it will work (some comments there about it though,
on that gerrit page).
I've also set CBFS size to 8MB, not the full size of
the BIOS region; this is required on the T440p which
uses the same mrc.bin file, to get S3 working.
TSEG stage cache disabled, as on other Haswell boards.
The setup: SeaBIOS-only as first payload, but with GRUB
enabled as secondary payload. The _grubonly setup has
been enabled here. This way, the config will work on
iGPU and dGPU setups without issue.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
coreboot gerrit patch 55232, patchset 31
the actual board will be enabled in a follow-up patch.
merging the patch on its own first is better practise,
to run ./update trees -u coreboot
this way, there won't be a revision that breaks builds,
due to the idiosyncratic nature of coreboot configuration.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
Riku introduced three new patches:
* Add support for multiple chip selects. This allows you to
control multiple chips from the same clip, on systems with
dual flash setups, at least theoretically.
* Enable pull-up on unused chip selects - pull them high so
that chips you connect that to are deactivated while flashing
the target chip. This could be used on thinkpad W541 for
instance, where miso/mosi have 0ohm between them via the two
flash ICs. You could pull the other chip select high.
* Documentation for the above, in the pico-serprog readme.
This goes in tandem with a patch from Riku, present in the
recently integrated flashprog project, namely:
commit ddb6d926783d4f9cbee04c7392718ed8f89daa0e
Author: Riku Viitanen <riku.viitanen@protonmail.com>
Date: Mon Jan 15 19:15:49 2024 +0200
serprog: Add support for multiple SPI chip selects
This functionality will therefore be present in the next
release of Libreboot.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
from Riku_V/lbmk:master into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/180
|
|
|
|
we use flashprog now!
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Nico Huber is the rightful project lead. I do not support
the coup that occured within the flashrom project. Nico
has always been of great service to the Libreboot project,
by virtue of his work on both coreboot and flashrom.
Nico Huber was unfairly removed from the flashrom project
infrastructure, due to unfounded accusations hurled at him
by flashrom's new project lead. The accusations are unfounded
because no evidence was given.
Use Nico Huber's fork, named flashprog. We will work with
flashprog from now on.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it's still necessary here, to prevent the same bug
identified in the previous patch.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
in some cases, the build system was needlessly, and sometimes
erroneously, creating crossgcc symlinks, which then caused an
issue, namely:
in lbmk release builds, dell e6400 is build before fam15h boards,
and it sets xtree, but fam15h_rdimm doesn't, and later this would
cause fam15h_rdimm boards to use xtree="default" (because they don't
set xtree), causing the newer toolchain to be used on coreboot 4.11.
this patch fixes the issue. quite a simple problem, actually.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
CONFIG_PS2M_EISAID. this is a a string used for the
identifier on the mouse, in ACPI.
CONFIG_PS2K_EISAID this is used for the keyboard.
IASL comes back with this build error:
dsdt.asl 1884: Name(_HID, EISAID("DLLK0534"))
Error 6045 - ^ EISAID string must be of the form "UUUXXXX" (3 uppercase, 4 hex digits) (DLLK0534)
Change DLLK0534 back to PNP0303 and
change DLL0534 back to PNP0F13. These are generic identifiers
for PS/2 keyboard and mouse. Any generic driver will work with
the onboard mouse/keyboard on these machines. They do not need
to be changed. These are the default values anyway. Just leave
them explicitly defined to the default values, for now; if these
options are not set, coreboot will default to these values.
This shouldn't break anything for the users. I've reported this
to Nicholas Chin, author of those patches. Libreboot imported
the new versions of E6430/E6530 board patches in the coreboot
revision update, but the new (technically correct) values broke
IASL, so I've decided to use the old values for now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
