summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-03-18Merge pull request 'util: Import autoport with Haswell patches' (#195) from ↵Leah Rowe
nic3-14159/lbmk:autoport-fork into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/195
2024-03-18util: Import autoport with Haswell patchesNicholas Chin
This is a copy of coreboot's autoport utility, with a patch applied to support Haswell/Lynx Point platforms. That patch is currently in review on coreboot's Gerrit. https://review.coreboot.org/c/coreboot/+/30890 Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-03-16dell-flash-unlock: add NetBSD supportlinear cannon
2024-03-12Merge pull request 'Use proper autolink' (#192) from eo/lbmk:master into masterLeah Rowe
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/192
2024-03-05Use proper autolinkLeo Heitmann Ruiz
2024-03-04config: Add Dell Latitude E5420Nicholas Chin
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-03-02coreboot/dell9020*_12mb: Disable IOMMU by defaultLeah Rowe
Needed to make graphics cards work. Turn it on if you're using only the Intel GPU. With IOMMU *enabled*, graphics cards do not work reliably at all. The cause still needs to be investigated, but the symptoms are graphical corruption on the screen, and Xorg usually crashes. In some cases (on some cards), TTYs can still be used; the payload can still be used reliably, on a graphics card, but Xorg fails to work properly. This could be a bug in Linux drivers, instead of anything that coreboot does (not yet tested in factory BIOS). Leaving it off by default will ensure reliable operation on all setups, whether an iGPU or dGPU is used. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-03-02coreboot/haswell: make IOMMU a runtime optionLeah Rowe
It is now possible to disable the IOMMU on Haswell boards, by doing this on your ROM image: ./nvramtool -C libreboot.rom -w iommu=Disable To enable it again, do this: ./nvramtool -C libreboot.rom -w iommu=Enable If not specified, the default behaviour is *on*. A follow-up patch will turn IOMMU *off* by default, on Dell OptiPlex 9020 SFF/MT, by setting it as such in cmos.default. This is to make graphics cards work properly to work around a bug when it's turned on. Leaving the IOMMU enabled is recommended, if it works. It works in most cases, including on 9020 SFF/MT when using the Intel GPU without a graphics card inserted. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-27enable serial console on fam15h boardsLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-25Libreboot 2024022520240225Leah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-23config/vendor: fix entry for 9020sffLeah Rowe
the current entry is fine, but it would then not support other configs of different flash sizes, unless they are explicitly defined. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-23disable hiding peg from mrc on dell 9020Leah Rowe
makes graphics cards work Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-21Merge pull request 'config/ifd/dell_ivybridge: Add ifd_nogbe' (#188) from ↵Leah Rowe
nic3-14159/lbmk:add-dell-ivb-ifd-nogbe into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/188
2024-02-20config/ifd/dell_ivybridge: Add ifd_nogbeNicholas Chin
This is required by the Latitude E5530, which uses a Broadcom NIC instead of the Intel ones. The original port was missing this file. Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-18./update trees -u corebootLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-18NEW BOARD: dell 9020 optiplex sffLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-17Merge pull request 'Add HP EliteBook 8560w, MXM' (#187) from ↵Leah Rowe
Riku_V/lbmk:hp8560w into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/187
2024-02-12Add HP EliteBook 8560wRiku Viitanen
Iru Cai's port from Gerrit: https://review.coreboot.org/c/coreboot/+/39398 Now with the proper MXM structure, which removes the 30 second POST delay. Tested with i7-2670QM, Quadro 2000M and 32GB RAM. Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
2024-02-11update pico-serprog to new revisionLeah Rowe
this merges the fix from: https://codeberg.org/libreboot/pico-serprog/pulls/1 however, PRs are not to be sent there. riku merged it in his repository, and i pulled it in the mirror hosted on libreboot codeberg Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-11Patch SeaBIOS: Add MXM supportRiku Viitanen
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
2024-02-08Merge pull request 'Add Dell Latitude E5520' (#184) from ↵Leah Rowe
nic3-14159/lbmk:latitude-ports into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/184
2024-02-08config: Add Dell Latitude E5520Nicholas Chin
Tested by Minimum_Baseball_629 on Reddit Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-08config/coreboot/default/patches : Renumber E6420, E6520, E5530 patchesNicholas Chin
The OptiPlex 9020/7020 port was merged first and was numbered 31. Increment the numbering of the Latitude patches to reflect this. Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-08coreboot/dell9020mt: disable pcie rebarLeah Rowe
i enabled it but it's buggy according to comments on gerrit. disable for now. dgpu didn't work anyway, even with it turned off, when i had this tested. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-08remove coreboot/dell9020mtvga_12mbLeah Rowe
keep dell9020mt_12mb dell9020mtvga_12mb doesn't actually work (was tried for running a graphics card on its own, with no igpu init) Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-07Merge pull request 'update revision: pico-serprog' (#185) from ↵Leah Rowe
Riku_V/lbmk:master into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/185
2024-02-07update revision: pico-serprogRiku Viitanen
should fix https://codeberg.org/libreboot/lbmk/issues/182 Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
2024-02-07update coreboot configsLeah Rowe
this was done automatically by running: ./update trees -u coreboot this has to be done when adding patches for now board ports, because of the way lbmk and also coreboot's build systems work. the configs just have to be re-generated to include a line that says the entry for the newly added boards isn't set. look at the diff of this commit as an example. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-02-07Merge pull request 'Add Latitude E6420, E6520, and E5530' (#183) from ↵Leah Rowe
nic3-14159/lbmk:latitude-ports into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/183
2024-02-07support making u-boot-only tarballs in releasesLeah Rowe
./update release -m u-boot if someone just wants to make u-boot, they can use this and it tars up all the trees. Signed-off-by: Leah Rowe <info@minifree.org>
2024-02-06config: Add Dell Latitude E5530Nicholas Chin
Tested by Martin Dawson. Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-06config: Add Dell Latitude E6520Nicholas Chin
Tested by Martin Dawson. Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-06config: Add Dell Latitude E6420Nicholas Chin
Tested by Martin Dawson. Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
2024-02-04add vga-only 9020 configLeah Rowe
on a dgpu setup, igpu was still in use, when tested by a user. do separate roms that don't enable anything vga in coreboot, relying instead only on seabios to execute a vga rom. these roms will only work if you have a graphics card. Signed-off-by: Leah Rowe <info@minifree.org>
2024-02-04NEW BOARD: Dell OptiPlex 9020 MT (and 7020 MT)Leah Rowe
Specifically the MT versions. The SFF versions will be added separately, in a later commit. See: https://review.coreboot.org/c/coreboot/+/55232 This patch has been added, from patchset 31. It still has some unresolved issues, on that patchset, but it should boot. See commit message there. Of note: I've enabled PCI REBAR, though it's unknown whether it will work (some comments there about it though, on that gerrit page). I've also set CBFS size to 8MB, not the full size of the BIOS region; this is required on the T440p which uses the same mrc.bin file, to get S3 working. TSEG stage cache disabled, as on other Haswell boards. The setup: SeaBIOS-only as first payload, but with GRUB enabled as secondary payload. The _grubonly setup has been enabled here. This way, the config will work on iGPU and dGPU setups without issue. Signed-off-by: Leah Rowe <info@minifree.org>
2024-02-03import dell optiplex 7020/9020 patch from gerritLeah Rowe
coreboot gerrit patch 55232, patchset 31 the actual board will be enabled in a follow-up patch. merging the patch on its own first is better practise, to run ./update trees -u coreboot this way, there won't be a revision that breaks builds, due to the idiosyncratic nature of coreboot configuration. Signed-off-by: Leah Rowe <info@minifree.org>
2024-01-28update pico-serprog to Riku's new revisionLeah Rowe
Riku introduced three new patches: * Add support for multiple chip selects. This allows you to control multiple chips from the same clip, on systems with dual flash setups, at least theoretically. * Enable pull-up on unused chip selects - pull them high so that chips you connect that to are deactivated while flashing the target chip. This could be used on thinkpad W541 for instance, where miso/mosi have 0ohm between them via the two flash ICs. You could pull the other chip select high. * Documentation for the above, in the pico-serprog readme. This goes in tandem with a patch from Riku, present in the recently integrated flashprog project, namely: commit ddb6d926783d4f9cbee04c7392718ed8f89daa0e Author: Riku Viitanen <riku.viitanen@protonmail.com> Date: Mon Jan 15 19:15:49 2024 +0200 serprog: Add support for multiple SPI chip selects This functionality will therefore be present in the next release of Libreboot. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-28Merge pull request 'flashprog: apply the good old MX25 workaround' (#180) ↵Leah Rowe
from Riku_V/lbmk:master into master Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/180
2024-01-28flashprog: apply the good old MX25 workaroundRiku Viitanen
2024-01-27remove remaining flashrom remnants (use flashprog)Leah Rowe
we use flashprog now! Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-27update parabola dependencies for flashprogLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-27update arch dependencies for flashprogLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-27update trisquel dependencies for flashprogLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-27update debian dependencies for flashprogLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-27config/git: use flashprog instead of flashromLeah Rowe
Nico Huber is the rightful project lead. I do not support the coup that occured within the flashrom project. Nico has always been of great service to the Libreboot project, by virtue of his work on both coreboot and flashrom. Nico Huber was unfairly removed from the flashrom project infrastructure, due to unfounded accusations hurled at him by flashrom's new project lead. The accusations are unfounded because no evidence was given. Use Nico Huber's fork, named flashprog. We will work with flashprog from now on. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-26Libreboot 2024012620240126Leah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-26git.sh: also reset xtree/tree_depend hereLeah Rowe
it's still necessary here, to prevent the same bug identified in the previous patch. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-26update/trees: reset xtree/tree_depend before buildLeah Rowe
in some cases, the build system was needlessly, and sometimes erroneously, creating crossgcc symlinks, which then caused an issue, namely: in lbmk release builds, dell e6400 is build before fam15h boards, and it sets xtree, but fam15h_rdimm doesn't, and later this would cause fam15h_rdimm boards to use xtree="default" (because they don't set xtree), causing the newer toolchain to be used on coreboot 4.11. this patch fixes the issue. quite a simple problem, actually. Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-25update config/git/docs to latest revsLeah Rowe
Signed-off-by: Leah Rowe <leah@libreboot.org>
2024-01-25dell/e6*30: use generic PS2K/PS2M EISAID stringsLeah Rowe
CONFIG_PS2M_EISAID. this is a a string used for the identifier on the mouse, in ACPI. CONFIG_PS2K_EISAID this is used for the keyboard. IASL comes back with this build error: dsdt.asl 1884: Name(_HID, EISAID("DLLK0534")) Error 6045 - ^ EISAID string must be of the form "UUUXXXX" (3 uppercase, 4 hex digits) (DLLK0534) Change DLLK0534 back to PNP0303 and change DLL0534 back to PNP0F13. These are generic identifiers for PS/2 keyboard and mouse. Any generic driver will work with the onboard mouse/keyboard on these machines. They do not need to be changed. These are the default values anyway. Just leave them explicitly defined to the default values, for now; if these options are not set, coreboot will default to these values. This shouldn't break anything for the users. I've reported this to Nicholas Chin, author of those patches. Libreboot imported the new versions of E6430/E6530 board patches in the coreboot revision update, but the new (technically correct) values broke IASL, so I've decided to use the old values for now. Signed-off-by: Leah Rowe <leah@libreboot.org>