summaryrefslogtreecommitdiff
path: root/util/e6400-flash-unlock/README.md
diff options
context:
space:
mode:
Diffstat (limited to 'util/e6400-flash-unlock/README.md')
-rw-r--r--util/e6400-flash-unlock/README.md102
1 files changed, 0 insertions, 102 deletions
diff --git a/util/e6400-flash-unlock/README.md b/util/e6400-flash-unlock/README.md
deleted file mode 100644
index bc9dd9f9..00000000
--- a/util/e6400-flash-unlock/README.md
+++ /dev/null
@@ -1,102 +0,0 @@
-# Dell Laptop Internal Flashing
-
-This utility allows you to use flashrom's internal programmer to program the
-entire BIOS flash chip from software while still running the original Dell
-BIOS, which normally restricts software writes to the flash chip. It seems like
-this works on any Dell laptop that has an EC similar to the SMSC MEC5035 on the
-E6400, which mainly seem to be the Latitude and Precision lines starting from
-around 2008 (E6400 era).
-
-## TL;DR
-Run `make` to compile the utility, and then run `sudo ./e6400_flash_unlock` and
-follow the directions it outputs.
-
-## Confirmed supported devices
-- Latitude E6400
-- Latitude E6410
-- Latitude E4310
-- Latitude E6430
-- Precision M6800
-
-It is likely that any other Latitude/Precision laptops from the same era as
-devices specifically mentioned in the above list will work as Dell seems to use
-the same ECs in one generation.
-
-## Detailed device specific behavior
-- On GM45 era laptops, the expected behavior is that you will run the utility
- for the first time, which will tell the EC to set the descriptor override on
- the next boot. Then you will need to shut down the system, after which the
- system will automatically boot up. You should then re-run the utility to
- disable SMM, after which you can run flashrom. Finally, you should run the
- utility a third time to reenable SMM so that shutdown works properly
- afterwards.
-- On 1st Generation Intel Core systems such as the E6410 and newer, run the
- utility and shutdown in the same way as the E6400. However, it seems like the
- EC no longer automatically boots the system. In this case you should manually
- power it on. It also seems that the firmware does not set the BIOS Lock bit
- when the descriptor override is set, making the 2nd run after the reboot
- technically unnecessary. There is no harm in rerunning it though, as the
- utility can detect when the flash is unlocked and perform the correct steps
- as necessary.
-
-## How it works
-There are several ways the firmware can protect itself from being overwritten.
-One way is the Intel Flash Descriptor (IFD) permissions. On Intel systems, the
-flash image is divided into several regions such as the IFD itself, Gigabit
-Ethernet (GBE) non-volative memory, Management Engine (ME) firmware, Platform
-Data (PD), and the BIOS. The IFD contains a section which specifies the
-read/write permissions for each SPI controller (such as the host system) and
-each region of the flash, which are enforced by the chipset.
-
-On the Latitude E6400, the host has read-only access to the IFD, no access to
-the ME region, and read-write access to the PD, GBE, and BIOS regions. In order
-for flashrom to write to the entire flash internally, the host needs full
-permissions to all of these regions. Since the IFD is read only, we cannot
-change these permissions unless we directly access the chip using an external
-programmer, which defeats the purpose of internal flashing.
-
-However, Intel chipsets have a pin strap that allows the flash descriptor
-permissions to be overridden depending on the value of the pin at power on,
-granting RW permissions to all regions. On the ICH9M chipset on the E6400, this
-pin is HDA\_DOCK\_EN/GPIO33, which will enable the override if it is sampled
-low. This pin happens to be connected to a GPIO controlled by the Embedded
-Controller (EC), a small microcontroller on the board which handles things like
-the keyboard, touchpad, LEDs, and other system level tasks. Software can send a
-certain command to the EC, which tells it to pull GPIO33 low on the next boot.
-
-Although we now have full access according to the IFD permissions, we still
-cannot flash the whole chip, due to another protection the firmware uses.
-Before software can update the BIOS, it must change the BIOS Write Enable
-(BIOSWE) bit in the chipset from 0 to 1. However, if the BIOS Lock Enable (BLE)
-bit is also set to 1, then changing the BIOSWE bit triggers a System Management
-Interrupt (SMI). This causes the processor to enter System Management Mode
-(SMM), a highly privileged x86 execution state which operates transparently to
-the operating system. The code that SMM runs is provided by the BIOS, which
-checks the BIOSWE bit and sets it back to 0 before returning control to the OS.
-This feature is intended to only allow SMM code to update the system firmware.
-As the switch to SMM suspends the execution of the OS, it appears to the OS
-that the BIOSWE bit was never set to 1. Unfortunately, the BLE bit cannot be
-set back to 0 once it is set to 1, so this functionality cannot be disabled
-after it is first enabled by the BIOS.
-
-Older versions of the E6400 BIOS did not set the BLE bit, allowing flashrom to
-flash the entire flash chip internally after only setting the descriptor
-override. However, more recent versions do set it, so we may have hit a dead
-end unless we force downgrade to an older version (though there is a more
-convenient method, as we are about to see).
-
-What if there was a way to sidestep the BIOS Lock entirely? As it turns out,
-there is, and it's called the Global SMI Enable (GBL\_SMI\_EN) bit. If it's set
-to 1, then the chipset will generate SMIs, such as when we change BIOSWE with
-BLE set. If it's 0, then no SMI will be generated, even with the BLE bit set.
-On the E6400, GBL\_SMI\_EN is set to 1, and it can be changed back to 0, unlike
-the BLE bit. But there still might be one bit in the way, the SMI\_LOCK bit,
-which prevents modifications to GBL\_SMI\_EN when SMI\_LOCK is 1. Like the BLE
-bit, it cannot be changed back to 0 once it set to 1. But we are in luck, as
-the vendor E6400 BIOS leaves SMI\_LOCK unset at 0, allowing us to clear
-GBL\_SMI\_EN and disable SMIs, bypassing the BIOS Lock protections.
-
-There are other possible protection mechanisms that the firmware can utilize,
-such as Protected Range Register settings, which apply access permissions to
-address ranges of the flash, similar to the IFD. However, the E6400 vendor
-firmware does not utilize these, so they will not be discussed.