| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the current validation check is extremely over-engineered,
because the user override is no longer available and we're
always very careful in how we modify target.cfg per board.
remove the redundant code. trust that target.cfg is correct.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
p = payload
s = grub_scan_disk
d = displaymode
setting the payload is no longer safe, due to issue 216
and similar issues that might pop up in the future; it's
best left only to target.cfg, per board, so that we know
what config is safe/tested. don't let the user override it.
scandisk isn't safe to override because the given machine
may not have the type of device that the user specifies
displaymode is actually ok to set, because it simply whitelists
what configs pre-existing to actually use, but it's bloat
basically, the rule is this:
don't make it easy for the user to brick their hardware.
make it harder instead.
a user wily enough to go modifying their payload will probably
have read docs/maintain/ anyway and knows how to edit target.cfg
if they want another board configuration.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
new function chkvars() does the job
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it's pretty much just doing the same thing as ls -1
remove it!
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i removed this before, when making grub multi-tree,
because the design i used in an earlier version of
the patch actually added the grub.elf generation
to grub source itself, but then i decided to hack
around the grub build system from lbmk/cbmk instead
re-add this functionality, so that users can easily
insert their own custom grub.cfg into cbfs without
needing to re-build their image.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i was originally looser about this, because i also wanted
the trees script to generically run "make" from any
directory, but this behaviour was error-prone and it is
no longer used in the build system.
disable it, in the interest of stability.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
support redundant downloads, and enable inclusion of these
tarballs inside release archives, for offline builds.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
don't create elfdir, create dest_dir, which is elfdir
plus the location within it
only create dest_dir within copy_elf, which is only
called if actually compiling the code
this avoids creating empty elf directories, and it
generally cleans up all handling, unifying the
handling of directories into a single function,
namely copy_elf() which already exists
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
don't do it after, because that means the main project
is saved under src/ before we know whether the subrepo
was downloaded.
the "depend" variable (in config/git/) is no longer used
for projects that go in subdirectories of a parent; now,
we use config/submodules/ for this type of dependency.
download the "depend" projects (as per config/git/) first.
this way, if they fail, the main one will fail, but if
they succeed and main fails, you can just run the main
download again and it won't fail.
this fixes a bug where, depending on how you download a
set of projects and depending on the order which you do so,
a given project can become un-downloadable on current design,
because git will complain that a directory already exists.
this fix is done not only in code (by this commit), but
by prior configuration changes.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it could lead to some whackiness later on
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
we're not checking for bad elfs, but the check itself was bad
due to a quirk in how sh works. really, really obscure bug.
fixed now!
if the given directory didn't actually exist, or there were no
files in it, it'd be searching for the file named "*"
which is obviously wrong
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
don't check that the variable is empty
check that the file itself exists or not
this should fix the recent build issues
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
(on single tree projects. this complements the last patch)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
otherwise, some checks are done too soon, and nothing
gets built.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
in particular, the coreboot build system may auto-download
submodules when building cbfstool; vboot for instance.
we do not want such unpredictable behaviour, so now we
use UPDATED_SUBMODULES=1 when building coreboot utilities.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it doesn't really make sense placed in lib.sh,
because it's only called from script/trees
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
one directory per util, under elf/
e.g. elf/cbfstool/
further split by tree name, e.g.:
elf/cbfstool/default/
elf/cbfstool/foo/
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
this replicates the same behaviour as multi-tree builds,
checking for files inside the relevant elf/ directory
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the previous change makes memtest.bin get cached in elf/
but the path was being prefixed with src/ by script/roms
do away with the prefix
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
e.g. ./update trees -b flashprog
tell the user to check elf/flashprog
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
for example, now flashprog binaries could be placed
in the elf/ directory, under elf/flashprog/
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it's also used from script/roms, in addition to trees
move these variables to a common file used everywhere
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
certain code checks for build.list, to skip it, for
example in items()
we already use config/data/grub to store grub config data
that applied to all trees
create these directories too:
config/data/coreboot
config/data/u-boot
config/data/seabios
move the respective build.list files in here, and also
to config/data/grub
now multi-tree projects contain, per directory, just the
target.cfg file and the patches directory. this is much
cleaner, because some of the logic can be simplified more
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
instead, check for the presence of target.cfg files
not in config/project/ but config/project/tree/
the way this check is done, it merely returns 1 if
config/project/*/target.cfg is detected, and returns
0 in all other cases, even if config/project/target.cfg
exists
that way, if the maintainer accidentally adds a
target.cfg in the main directory, the given multi-tree
project will not break
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
adding help again is a bad idea. code should never
document itself; that's what documentation is for.
so, make the code do a better job telling the user
where to find documentation.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Re-add xHCI only on haswell and broadwell machines, where
they are needed. Otherwise, keep the same GRUB code.
The xHCI patches were removed because they caused issues
on Sandybridge-based Dell Latitude laptops. See:
https://codeberg.org/libreboot/lbmk/issues/216
The issue was not reported elsewhere, including on the
Haswell/Broadwell hardware where they are needed, but the
build system could only build one version of GRUB.
The older machines do not need xHCI patches, because they
either do not have xHCI patches, or work (in GRUB) because
they're in EHCI mode when running the payload.
So, the problem is that we need the xHCI patches for GRUB
on Haswell/Broadwell hardware, but the patches break
Sandybridge hardware, and we only had the one build of GRUB.
To mitigate this problem, the build system now supports
building multiple revisions of GRUB, with different patches,
and each given coreboot target can say which GRUB tree to use
by setting this in target.cfg:
grubtree="xhci"
In the above example, the "xhci" tree would be used. Some
generic GRUB config has been moved to config/data/grub/
and config/grub/ now looks like config/coreboot/ - also,
the grub.cfg file (named "payload" in each tree) is copied
to the GRUB source tree as ".config", then added to GRUB's
memdisk in the same way, as grub.cfg.
Several other design changes had to be made because of this:
* grub.cfg in memdisk no longer automatically jumps to one
in CBFS, but now shows a menuentry for it if available
* Certain commands in script/trees are disabled for GRUB,
such as *config make commands.
* gnulib is now defined in config/submodule/grub/, instead
of config/git/grub - and this mitigates an existing bug
where downloading gnulib first would make grub no longer
possible to download in lbmk.
The coreboot option CONFIG_FINALIZE_USB_ROUTE_XHCI has been
re-enabled on: Dell OptiPlex 9020 MT, Dell OptiPlex 9020 SFF,
Lenovo ThinkPad T440p and Lenovo ThinkPad W541 - now USB should
work again in GRUB.
The GRUB payload has been re-enabled on HP EliteBook 820 G2.
This change will enable per-board GRUB optimisation in the
future. For example, we hardcode what partitions and LVMs
GRUB scans because * is slow on ICH7-based machines, due
to GRUB's design. On other machines, * is reasonably fast,
for automatically enumerating the list of devices for boot.
Use of * (and other wildcards) could enable our GRUB payload
to automatically boot more distros, with minimal fuss. This
can be done at a later date, in subsequent revisions.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
this effectively lets you change the boot order. example:
./build roms -s "nvme ata" t1650_12mb
the above example would set:
grub_scan_disk="nvme ata"
another example:
./build roms -s nvme t1650_12mb
this would set:
grub_scan_disk="nvme"
this overrides what's set in target.cfg for the given
target. useful for quick reconfiguration if building
from source
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i already do this on crossgcc, but overlooked it on regular
builds where i just use -j, but coreboot's build system
makes use of the CPUS= option in make
use XBMK_THREADS for this
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Previously, grub_scan_disk could set ata, ahci or "both",
which would make both be tried (ahci first). This worked
when we only dealt with ata and ahci devices, but now we
support nvme devices so the logic is inherently flawed.
Instead, use grub_scan_disk to store the boot order, e.g.:
grub_scan_disk="ahci nvme ata"
grub_scan_disk="nvme ata"
In the first example, it would make GRUB scan ahci first,
then nvme and then ata.
In the secontd example, it would make GRUB scan nvme first,
and then ata.
If "both" is set, or anything other than ahci/ata/nvme,
grub_scan_disk is now changed to "nvme ahci ata".
Actual grub_scan_disk entries in target.cfg files will now
be modified, to match each machine.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
rather than if seabios_grubonly=y
if grubonly=y, still make the grubonly rom
this complements the previous commit
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i forgot to do this in the recent cleanup. it is now
initialised as a variable named "x"
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it wasn't being reset before. when coreboot is being
built, i add to makeargs every time. if multiple targets
are being built, the make command would end up looking
something like:
make -C src/coreboot/default UPDATED_SUBMODULES=1 \
UPDATED_SUBMODULES=1
(the parameter would be printed twice)
of course, this doesn't check whether that parameter is
added already in target.cfg for a given target, but that's
ok because i won't add that one in target.cfg
i baked it into the code, only when handling coreboot,
because that was easier than either putting it in makeargs
for every coreboot target.cfg, or again modifying the code to
handle that; the current solution is the cleanest.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i overlooked this in the previous revision
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
we do not want submodules to be downloaded after the fact.
we only handle this on ./update trees -f coreboot
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
firstly, memtest86+ is currently not cross compiled and
relies on 64-bit headers (x86_64 only). a 32-bit distro
is unlikely to be able to build 64-bit binaries.
secondly: vboot throws a build error due to -Werror when
building on 32-bit hosts. we rely on vboot code to build
cbfstool, so turn off -Werror on vboot
that's all. 32-bit hosts are not recommended; it is assumed
that you are building on an x86_64 host. work will go into
the build system at a later date to make it more portable,
by cross compiling everything, but this should fix 32-bit
for now.
there are some x60/t60 users who still want to build roms,
so let's allow them that possibility.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
fixes a regression when running ./build roms all
now it should work again
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
that's all it's used for, to compress the rom images
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it copies, it doesn't move, so name it right
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
