| Age | Commit message (Collapse) | Author |
|---|
|
Normally U-Boot immediately resets the board on a panic. I had run into
"Synchronous Abort"s from shim and rEFInd, and having a traceback in
those cases can be useful. Hang instead of resetting, so the panic
reason stays on the screen.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
We should be able to power the board off from U-Boot command line.
Enable the "poweroff" command for gru boards so we can.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
U-Boot can keep a "copy" framebuffer to read from, for devices where
reading from hardware framebuffer is expensive. This needs the video
driver to support it. The Rockchip video driver doesn't need or support
it, so this option does nothing on gru boards. Disable it.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
U-Boot upstream used to have 16KB for EFI variables, and this was
causing problems with shim. Commit f0236acbc663 ("u-boot: Increase EFI
variable buffer size") fixed this by raising it to 32KB in our builds.
It has now been raised to 64K upstream, so raise it here as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
For Rockchip boards U-Boot tries to build SPI and MMC images that
require an externally built BL31 file to be provided, and the build
fails otherwise. This is not really as configurable as it should be.
In Libreboot, we only care about the build outputs for U-Boot proper.
There is a BL31 built during our coreboot builds, but using that in
U-Boot builds is a chicken-and-egg problem. Building BL31 outside the
coreboot build and passing it to both projects is possible, but needs
work.
For now, stop trying to build these U-Boot-only images as a workaround,
by removing the binman image descriptions from the device-tree sources.
Additionally, disable in our configs the BINMAN_FDT functionality that
allows using these at runtime as it requires them to be present.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
U-Boot upstream has added a reference counting for regulator enable
actions which somehow makes gru-kevin unbootable. Add a workaround
that makes it work again.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
Set default U-Boot revision to v2023.01 and rebase patches on top of
that. Another series about 16x32 fonts was merged upstream, so drop some
now-unnecessary patches we had for that. For the video damage tracking
series, switch to the version I'm trying to upstream.
Upstream kconfig status is a bit unstable, so updating configs with
`make oldconfig` would miss important upstream changes, since they rely
on carrying defaults via upstream defconfigs. Update the configs as
such:
- Turn old configs into defconfigs (./update project trees -s u-boot)
- Save the diff from old upstream defconfig (diffconfig $theirs $ours)
- Update U-Boot revision, rebase patches, and clean old trees
- Prepare new U-Boot tree (./update project trees -f u-boot)
- Review the diffconfigs to see if any options were renamed upstream
- Copy over the new upstream defconfigs and apply earlier diff
- Turn new defconfigs into configs (./update project trees -l u-boot)
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
The U-Boot build for qemu_arm64_12mb board refers to a code revision
whereas it uses the common "default" tree, remove the bad reference.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
The "u-boot.bin" file generated by U-Boot builds is a raw binary. When
adding payloads to a CBFS, we need to use ELF files with add-payload
or manually pass the entry point and load address of the payload binary
with add-flat-binary.
We primarily use the "u-boot.elf" which gets build with the REMAKE_ELF
option, as it also has the necessary device-tree binary that U-Boot
usually needs to work. When the option is not set (e.g. for QEMU), we
need to use the "u-boot" file which is an ELF.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
