| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
raminit has never been fully reliable on this board, and so
this board has never been stable. so, now that lbmk specifies
such status per board, mark these boards as such.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
export LBMK_VERSION_TYPE=x
x can be: stable, unstable
in target.cfg files, specify:
status=x
x can be: stable, unstable, broken, untested
if unset, lbmk defaults to "unknown"
if LBMK_VERSION_TYPE is set, no confirmation is asked
if the given target matches what's set (but what's set
in that environmental variable can only be stable or
unstable)
if LBMK_RELEASE="y", no confirmation is asked, unless
the target is something other than stable/unstable
"unstable" means it works, but has a few non-breaking
bugs, e.g. broken s3 on dell e6400
whereas, if raminit regularly fails or it is so absolutely
unreliable as to be unusable, then the board should be
declared "broken"
untested means: it has not been tested
With this change, it should now be easier to track whether
a given board is tested, in preparation for releases. When
working on trees/boards, status can be set for targets.
Also: in the board directory, you can add a "warn.txt" file
which will display a message. For example, if a board has a
particular quirk to watch out for, write that there. The message
will be printed during the build process, to stdout.
If status is anything *other* than stable, or it is unstable
but LBMK_VERSION_TYPE is not set to "unstable", and not building
a release, a confirmation is passed.
If the board is not specified as stable or unstable, during
a release build, the build is skipped and the ROM is not
provided in that release; this is in *addition* to
release="n" or release="y" that can be set in target.cfg,
which will skip the release build for that target if "n"
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
On T60 with Libreboot 20231106 and the GRUB payload, a user
reported this error in GRUB when a battery was connected:
"alloc magic is broken at 0x7b1aedf0: 0"
This error disappears when a battery is not connected, or
when using Libreboot 20230625. The issue has persisted
through to LIbreboot 20240225 and after, and I believe the
issue will be somewhere in coreboot, not in GRUB itself.
For now, switch i945 laptops (X60, T60, Macbook2,1) back to
the February 2023 coreboot revision used in Libreboot 20230625.
A bisect can be done before the next Libreboot release, ETA
May 2024, if time permits. Otherwise, this revert should solve
the problem for now, at least so far as Libreboot is concerned.
The following coreboot patches have been backported:
commit 29030d0f3dad2ec6b86000dfe2c8e951ae80bf94
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Sat Oct 7 01:32:51 2023 +0800
drivers/pc80/rtc/option.c: Stop resetting CMOS during s3 resume
Further patches from upstream:
commit 432e92688eca0e85cbaebca3232f65936b305a98
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Fri Nov 3 12:34:01 2023 +0800
drivers/pc80/rtc/option.c: Reset only CMOS range covered by checksum
These patches fixed S3 on GM45 machines, though it will be useful on
the i945 machines aswell.
The reason I'm doing it this way it is because I don't have a battery
for my X60 or T60, and my T60 isn't in a very good state either,
so I can't reproduce the error myself yet.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i added mkukri's patch but didn't enable it. this was intentional.
this patch enables tpm by default, on all 9020 sff/mt targets.
most users probably won't need it, but enabling it won't hurt.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
at present, the inject scripts compress refcode in a way
that is not reproducible, so there's no way to verify
that the firmware is correct, via checksum verification,
when injecting vendor code on release images
the lack of reproducibility in recompression will have to be
addressed, but the issue is that lbmk does not provide its own
sources for compression utilities, instead opting to use the
system's own compression utility
so the solution might be for lbmk not to use the host's utility,
and compile its own, or insert the refcode uncompressed. for now,
simply disable the hp 820 g2 target in libreboot releases
this uses the same logic recently implemented for excluding
mrc-based haswell images in libreboot releases
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
release="n" is set in target.cfg on haswell build targets
that use mrc.bin
script/update/release exports LBMK_RELEASE="y"
script/build/roms skips building a given target if release="n"
in target.cfg *and* LBMK_RELEASE="y"
you could also do the export yourself before running ./build roms,
for example:
export LBMK_RELEASE="y"
./build roms all
This would skip these ROM images. The native haswell raminit is
now stable enough in my testing, that I wish to delete the MRC-based
targets. This is in line with Libreboot's Binary Blob Reduction Policy,
which states: if a blob can be avoided, it should be avoided.
The problem is that users often run the inject script in *lbmk* from
Git, instead of from the src release archive. I forsee some users
running this on modern lbmk with older release images. If the mrc-based
target isn't there, the user may use an NRI-based target name, and
think it works; they will insert without MRC. I foresaw this ages
ago, which is why Caleb and I ensured that the script checks hashes,
and hashes are included in releases.
Therefore: for the time being, keep the MRC-based configs in lbmk
but do not include images for them in releases. This can be done
indefinitely, but I'll probably remove those configs entirely at
some point.
On the following boards, Libreboot now will *only* provide NRI-based
ROM images for the following machines:
* Dell OptiPlex 9020 SFF
* Dell OptiPlex 9020 MT
* Lenovo ThinkPad T440p
* Lenovo ThinkPad W541/W540
I now recommend exclusive use of NRI-based images, on Haswell
hardware. It's stable enough in my testing, and now supports S3.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
sff happened to work, but mt would not boot with the patch,
because it called die() on unknown chassis type, and the gpio
happened to have a bad value in the old patch, because it wasn't
reading the right gpio.
i tested the fix on the old patch, but then decided to use
mate's new patch because instead of calling die(), it simply
boots with fan control disabled (max fan speed in that case),
if this happens again.
mt and sff have both been tested with this new version of the
patch. both of them boot, and they both have proper fan control.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
a hangover from earlier days, but i still disable it. i forgot
to do so on this config, when updating the nri code. do it now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
hell added a patch fixing S3 on haswell NRI, but it seems
you still need to set 8MB CBFS size as with the MRC
tested on a t440p. S3 now works on haswell NRI.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the t440p/w541 configs were re-done from scratch, because
the coreboot revisions are nearly two years apart.
i also added corebootfb configs.
hell updated their patchset. this patchset uses the following patch:
https://review.coreboot.org/c/coreboot/+/81948/1
it uses this, along with parent patches in the haswell nri patch series
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
see:
https://review.coreboot.org/c/coreboot/+/81529
what i've merged is patchset 4. i had to rebase it slightly,
because the libreboot version has the iommu toggle on cmos
configs, which are files that mate's patch also changes,
leading to merge conflict.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the grub payload was previously disabled, because the libre
mrc code sets up xhci rather than ehci, and grub did not have
xhci support (not natively).
libreboot now has xhci support in the grub payload, so enable
grub on these configurations.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
broadwell mrc enables both igpu and dgpu to be enabled
at any given time. if the onboard (intel) gpu is set as
primary, the logic to disable it is not executed within
coreboot; instead, the igpu is used for vga decode.
on some t440p/w541 thinkpads, both an intel and nvidia
gpu are present. in this setup, the intel gpu must be
used for vga, and all output, but rendering can be
offloaded to the nvidia gpu (nvidia optimus).
optimus would never work on haswell mrc.bin, because it
always disables the igpu when a dgpu is present, so a hack
exists in coreboot that hides the dgpu from mrc, so that the
igpu remains enabled. broadwell mrc doesn't do this, so the
option to hide PEG devices has been disabled in these
configs.
the broadwell mrc has better peg device handling, and can
support 16gb modules on broadwell hardware; it may well
support these modules on haswell hardware too, though ddr3
sodimms are very hard to find (and expensive). (and currently
untested, with this patch)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
broadwell mrc has better peg handling and can support 16gb
modules on broadwell machines - the blob can be used on haswell
machines too, instead of haswell mrc, and it might support 16gb
modules on these machines (not yet tested, but using broadwell
mrc does at least boot as reliably as haswell mrc anyway)
one little quirk with haswell mrc is that it actually handles
vga decode, disabling the igpu entirely, when a dgpu is used.
the broadwell mrc enables both GPUs and does not handle vga
decoding, so we must handle this the usual way; my patch for
this was merged upstream and i'm also adding it to libreboot,
which currently uses an older coreboot revision. this is needed
for dgpu to work. see patch:
0040-nb-haswell-Disable-iGPU-when-dGPU-is-used.patch
broadwell mrc may also make dealing with nvidia optimus setups
more reliable, on laptops that have nvidia GPUs, but this patch
does not add bmrc configs for t440p/w541
NOTE: on t440p/w541 laptops with nvidia graphics, the video output
is wired to intel but rendering can be offloaded to nvidia. in this
setup, we want vga decode to be done on intel, so i've set these
configs to enable CONFIG_ONBOARD_VGA_IS_PRIMARY (set it to y)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
3rd sata slot (of 3) broken on 9020 sff, and the 3rd and 4th (of 4)
slots are broken on 9020 mt
this patch fixes them on both, so that all ports work properly
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Needed to make graphics cards work. Turn it on if you're using
only the Intel GPU.
With IOMMU *enabled*, graphics cards do not work reliably at all.
The cause still needs to be investigated, but the symptoms are
graphical corruption on the screen, and Xorg usually crashes.
In some cases (on some cards), TTYs can still be used; the payload
can still be used reliably, on a graphics card, but Xorg fails to
work properly.
This could be a bug in Linux drivers, instead of anything that
coreboot does (not yet tested in factory BIOS).
Leaving it off by default will ensure reliable operation on all
setups, whether an iGPU or dGPU is used.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
It is now possible to disable the IOMMU on Haswell
boards, by doing this on your ROM image:
./nvramtool -C libreboot.rom -w iommu=Disable
To enable it again, do this:
./nvramtool -C libreboot.rom -w iommu=Enable
If not specified, the default behaviour is *on*.
A follow-up patch will turn IOMMU *off* by default,
on Dell OptiPlex 9020 SFF/MT, by setting it as such
in cmos.default. This is to make graphics cards work
properly to work around a bug when it's turned on.
Leaving the IOMMU enabled is recommended, if it works.
It works in most cases, including on 9020 SFF/MT when
using the Intel GPU without a graphics card inserted.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
makes graphics cards work
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Riku_V/lbmk:hp8560w into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/187
|
|
Iru Cai's port from Gerrit:
https://review.coreboot.org/c/coreboot/+/39398
Now with the proper MXM structure, which removes the 30 second POST
delay. Tested with i7-2670QM, Quadro 2000M and 32GB RAM.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
Tested by Minimum_Baseball_629 on Reddit
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
The OptiPlex 9020/7020 port was merged first and was numbered 31.
Increment the numbering of the Latitude patches to reflect this.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
i enabled it but it's buggy according to comments on gerrit.
disable for now. dgpu didn't work anyway, even with it turned
off, when i had this tested.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
keep dell9020mt_12mb
dell9020mtvga_12mb doesn't actually work (was tried for
running a graphics card on its own, with no igpu init)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
this was done automatically by running:
./update trees -u coreboot
this has to be done when adding patches for now board ports,
because of the way lbmk and also coreboot's build systems work.
the configs just have to be re-generated to include a line
that says the entry for the newly added boards isn't set. look
at the diff of this commit as an example.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
nic3-14159/lbmk:latitude-ports into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/183
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Tested by Martin Dawson.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
on a dgpu setup, igpu was still in use, when tested
by a user. do separate roms that don't enable anything
vga in coreboot, relying instead only on seabios to
execute a vga rom. these roms will only work if you
have a graphics card.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
Specifically the MT versions. The SFF versions will
be added separately, in a later commit.
See: https://review.coreboot.org/c/coreboot/+/55232
This patch has been added, from patchset 31. It still
has some unresolved issues, on that patchset, but
it should boot. See commit message there.
Of note: I've enabled PCI REBAR, though it's unknown
whether it will work (some comments there about it though,
on that gerrit page).
I've also set CBFS size to 8MB, not the full size of
the BIOS region; this is required on the T440p which
uses the same mrc.bin file, to get S3 working.
TSEG stage cache disabled, as on other Haswell boards.
The setup: SeaBIOS-only as first payload, but with GRUB
enabled as secondary payload. The _grubonly setup has
been enabled here. This way, the config will work on
iGPU and dGPU setups without issue.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
coreboot gerrit patch 55232, patchset 31
the actual board will be enabled in a follow-up patch.
merging the patch on its own first is better practise,
to run ./update trees -u coreboot
this way, there won't be a revision that breaks builds,
due to the idiosyncratic nature of coreboot configuration.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
CONFIG_PS2M_EISAID. this is a a string used for the
identifier on the mouse, in ACPI.
CONFIG_PS2K_EISAID this is used for the keyboard.
IASL comes back with this build error:
dsdt.asl 1884: Name(_HID, EISAID("DLLK0534"))
Error 6045 - ^ EISAID string must be of the form "UUUXXXX" (3 uppercase, 4 hex digits) (DLLK0534)
Change DLLK0534 back to PNP0303 and
change DLL0534 back to PNP0F13. These are generic identifiers
for PS/2 keyboard and mouse. Any generic driver will work with
the onboard mouse/keyboard on these machines. They do not need
to be changed. These are the default values anyway. Just leave
them explicitly defined to the default values, for now; if these
options are not set, coreboot will default to these values.
This shouldn't break anything for the users. I've reported this
to Nicholas Chin, author of those patches. Libreboot imported
the new versions of E6430/E6530 board patches in the coreboot
revision update, but the new (technically correct) values broke
IASL, so I've decided to use the old values for now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
re-use the same patches, and drop the same patches.
this tree uses hell's special ddr2 fix, which we apply
for the dell latitude e6400.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Base revision changed to:
commit b6cbfa977f63d57d5d6b9e9f7c1cef30162f575a
Author: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Date: Fri Jan 5 16:48:17 2024 +0800
mb/google/dedede/var/metaknight:Add fw_config probe for multi codec
and amplifier
Of note:
Several out-of-tree ports have been adjusted to use the new SPD config
style, where it is defined in devicetree. I manually updated the E6530
patch myself, based on the update that Nicholas did on E6430 (Nicholas
will later update the E6530 patch himself, and I'll re-merge the patch).
Several upstream patches now exist in this revision, that we were able
to remove from lbmk.
The heap size patch was reverted upstream, as we did, but see:
https://review.coreboot.org/c/coreboot/+/80023
https://review.coreboot.org/c/coreboot/+/79525
Although we still disable the TSEG Stage Cache, ivy/sandy/haswell should
be reliable on S3 now (leaving TSEG Stage Cache disabled, for now, anyway).
Also included in upstream now:
commit 29030d0f3dad2ec6b86000dfe2c8e951ae80bf94
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Sat Oct 7 01:32:51 2023 +0800
drivers/pc80/rtc/option.c: Stop resetting CMOS during s3 resume
Further patches from upstream:
commit 432e92688eca0e85cbaebca3232f65936b305a98
Author: Bill Xie <persmule@hardenedlinux.org>
Date: Fri Nov 3 12:34:01 2023 +0800
drivers/pc80/rtc/option.c: Reset only CMOS range covered by checksum
This should fix S3 on GM45 thinkpads.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
these should be using the rdimm tree for crossgcc,
so define it explicitly. the build system creates
a symlink too, but it's still best that we use it.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
in a build test, canoeboot 0.1 builds, but master doesn't,
and neither does lbmk. i changed a few of them when doing
the crossgcc build optimisation patches.
i'm just copying the configs from there. unlike in the
canoeboot version of this patch, i've re-enabled microcode
updates in these lbmk configs.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
a tree can specify:
tree_depend="treename"
this will make the other tree be downloaded. this is
used for coreboot trees, to ensure that dependency
trees are downloaded, because trees can now re-use
crossgcc from other trees.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
don't build crossgcc twice, especially if two coreboot
trees use the same revision!
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it's defined per board
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
work around newer build issues, on very bleeding edge distros
(disable treating warnings as errors)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
with neutered ME, fan control fails. while there are
ways to mitigate it, many users will not, and will
likely see their system overheat, which is very
dangerous.
this bug (failed fan control on neutered ME) only
affects arrandale machines such as lenovo x201.
the newer machines are not affected by this.
other arrandale machines will probably not be added
to libreboot because of this, or they will be subject
to further testing.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
