| Age | Commit message (Collapse) | Author |
|---|
|
don't handle "romtype" at all, in board target.cfg files
add /dev/null as pike2008 rom on amd boards. this serves
the same purpose, adding them as empty vga roms, to add
an empty rom in cbfs. pike2008 cards cause seabios to hang,
when their oproms are executed, so we insert a fake rom
on i945 thinkpads, use the coreboot config option:
CONFIG_INTEL_ADD_TOP_SWAP_BOOTBLOCK
when set, this enables the same bootblock copy, for use
with bucts. these two cases, namely pike2008 roms and
i945 bootblock copies, no longer need to be handled in code
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
the x220 edp patch invalidated lots of configs, so
i did: ./update trees -u coreboot
this is the resulting patch
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
only call crossgcc for coreboot and u-boot, but use
hostcc for everything else. simplify the checking of
which architecture to compile for. "arch" in target.cfg
files has been modified, to allow further simplification.
without this patch, the logic currently only *barely* avoids
using crossgcc on things like utils, and only works in practise
because, in practise, lbmk only works on x86_64 anyway.
the new logic, as per this patch, is simpler and more robust.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Inside the BIOS update, there's 68SCE and 68SCF variants.
Based on Qubes HCL and browsing linux-hardware.org, these are
Probook 6360b and Elitebook 8460p respectively.
I checked the KBC1126 EC Firmwares within the update file, both
use the exact same firmware images. Following-up will be a very
similar but untested port for 6360b.
Signed-off-by: Riku Viitanen <riku.viitanen@protonmail.com>
|
|
|
|
|
|
nic3-14159/lbmk:e6530 into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/151
|
|
Fix a few issues with the E6430 configs to make it consistent with
configs for other boards and function as intended.
- Add VBT to CBFS: Although the VBT was enabled at the board level
Kconfig in a previous commit (CONFIG_INTEL_GMA_HAVE_VBT), the config
to actually add the VBT to CBFS was still unset.
- Enable the static option table: The old config would always use the
fallback values hard coded in the coreboot tree, rather than the
settings in the cmos.default file
- Enable DRAM clear on boot: This was not set previously, even though
most other boards set this for security.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
This is pretty much the same as the E6430
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
This is to support future patches for other Ivy Bridge Dell Latitudes.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
the gnu.org 302 redirect often fails
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
nic3-14159/lbmk:enable-e6430-vbt into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/147
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
TSEG Stage Cache enabled again, because disabling it
did not affect S3 in any way.
Many configs have changed, and debug level is set to 7.
In testing with V-T60 on IRC, it wasn't just removal of
the DDR2 patch that I did, but I re-did the configs too,
in exactly the same way I've done them here, when testing
on an X200 to fix boot issues.
Libreboot does not use defconfigs, instead it uses full
configs, and these have to be updated. I normally just
run make-oldconfig on every config, for revision updates.
However, every now and then, we need to re-do them.
Play it safe and re-do every config. I've double- and
triple-checked that the configs are correct.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the ddr2 fix broke *ddr3* on gm45 thinkpads in
testing, depending on memory modules. this was
established by removing patches, re-doing
configs etc, on a user's X200 (testing gentoo
and freebsd). the X200 kept randomly rebooting
or having random glitches.
the configs themselves (gm45 thinkpads) will
also be re-done, because i found minor issues
unrelated, but this patch moves dell e6400 to
its own tree. the ddr2 fix is no longer present
in coreboot/default, only coreboot/dell.
i noticed minor differences in gm45 thinkpad
configs, when re-doing the configs, versus
what are currently in lbmk master; for instance,
vbt was not enabled anymore, on thinkpad x200.
modifications to these will be done separately.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
me_state=Disabled in cmos.default
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
The original E6430 patch included the Intel VBT file, but did not
actually enable it in Kconfig. Update the patch to enable it and
update the E6430 configs.
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it didn't work in the past, but it does work nowadays;
specifically, it only worked with libgfxinit in the past,
but not on VGA ROMs.
now it does work on VGA ROMs, tested on e6400 and t1650 so
it was enabled there.
in this setup, a special image is provided where SeaBIOS is
the main payload, but it only loads GRUB; nothing else, every.
this is called SeaGRUB. this setup is useful in cases where
the user only has a GPU that lacks libgfxinit support.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
libreboot configs' (#144) from fbraghiroli/lbmk:master into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/144
|
|
This reverts commit 29e9c32e32f8e947f51a3efe375dab3ef8e1987e.
|
|
this is to work around recent s3 suspend/resume issues
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
it's preferable that the vram setting be as high as
feasible, for users. we overlooked this on some
newer platforms that were added, over several
releases. these levels won't offend most users,
and people who want less can always turn it down
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
My previous fix to revert didn't fix S3 on GM45, one
of the platforms reported fixed by 78263; I'm merging
that instead, at patch set 10.
It is referenced by 78815/1 which was split from it,
so merge that too (restores overrides of higher values,
on certain platforms that we don't use yet).
https://review.coreboot.org/c/coreboot/+/78623/10
https://review.coreboot.org/c/coreboot/+/78815/1
Accordingly, update configs to match the new default.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
also, enable seabios_withgrub on e6400, but not grubfirst;
right now, we also support dgpu which would brick on
grubfirst. on my tested nvidia model, loading grub from
seabios worked, so i'm going to re-add seabios_grubfirst
functionality like in older libreboot revisions, enabled
selectively on a given target.
e6430 currently only has igpu support anyway, but i've done
the same thing there, in anticipation of future dgpu support.
e6400 and e6430 ec report scancode set 2 with translation
by default, but only actually output scancode set 1
grub is trying to use scancode set 2 without scancode
translation, so the key inputs get messed up
fix it by forcing scancode set 2 with translation, but
only on coreboot; other build targets on GRUB will
retain the same behaviour as before
courtesy goes to Nicholas Chin who inspired me, and
helped me to fix this. tested on Nicholas's E6400
and E6430, and my E6400; Riku also tested it on
non-Dell, as did I (some thinkpads), and all seems OK.
The new behaviour in coreboot GRUB is essentially no
different to that of SeaBIOS, which does the same.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
The original motherboard uses a 512kB flash chip size, however
I replaced the original chip with a bigger one (8MB).
|
|
the patch included in this revision is pulled from:
https://review.coreboot.org/c/coreboot/+/54024/2
contrary to hell's assertion of "not for merge", this does
in fact work nicely on a dell e6400; nicholas chin tested
on e6400 and found that those RCOMP values are the same
nicholas was testing some errant modules that seemed to
fail raminit in coreboot. in some cases, dell e6400 would
regularly fail coldboot even though reboot was ok; this was
therefore the cause of suspicioun for it being raminit-related
with this patch from hell (Angel Pons, but knows as hell
on IRC) it should fix boot issue on Dell Latitude E6400
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
patch courtesy of denis :)
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
note: me6_update_parser needs to be written, similar
to me7_update_parser, to generate the partition
tables within intel me6 on lenovo bios updates.
the current logic in lbmk goes like this:
mkdir -p vendorfiles/cache/
and save your factory dump as:
vendorfiles/cache/x201_factory.rom
the build system has been modified, in such a way
as to support extracting me.bin (which is the full
one) and then neutering from this.
this is done automatically, if the file is present,
but you must first insert that file there, which means
you'll need a dump of the original boot flash on your
thinkpad x201
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the patch:
https://review.coreboot.org/c/coreboot/+/78270
this has been reverted, because it caused s3 resume
issues on most intel laptops in libreboot.
i was going to merge this instead:
https://review.coreboot.org/c/coreboot/+/78623
however, it's under review, and this doesn't change
to the old behaviour; it keeps the new universal
config, but changes the default
we know the old logic works, so keep that for now.
in fact, the offending patch was only merged to
main in coreboot, one day before i recently
updated coreboot revs in coreboot/default - i used
a 12 october revision, the patch above is 11 october
i then ran "./update trees -u coreboot" which updated
the heap sizes back to the old defaults. this should
fix s3 suspend/resume where it was broken, in the
libreboot 20231021 release - a point release with this
and a few other fixes is planned soon.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the logic for naming coreboot roms is based on whether
cpu_microcode_blob.bin would exist in cbfs, and whether
deletion was therefore successful.
lbmk was naming nomicrocode on fam15h roms on this basis,
but the microcode was being inserted as microcode_amd.bin
and microcode_amd_fam15h.bin
in the recent 20231021 release, the roms were exclusively
labeled _nomicrocode in the rom names, but they do in fact
contain microcode.
i'm fixing it by telling lbmk *not* to delete microcode.
if microcode_required is not set, or it's set to y, then
only roms *with* microcode updates are provided; even if
the rom doesn't actually contain it, lbmk will only label
it _nomicrocode if that setting is set to n.
i'm not bothering to add further complexity to the rom
handling logic, because canoeboot now exists anyway (at
website https://canoeboot.org/) which is my new version
re-implementing the older, inferior version of libreboot
so i'm going to:
1) document this as errata in the release
2) cross reference in the freedom status page
3) if someone still isn't happy, i'll say use canoeboot
job done.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
princeton was down today. kent is probably more reliable.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Add a U-Boot build for the qemu_x86_12mb board. The config is a copy of
the upstream "coreboot" defconfig, but with OF_EMBED=y.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
github's httpd b0rked the fuck out and i didn't want to wait
for them to fix it (ssl cert error) before i continued a build.
i now host the relevant acpica tarball on libreboot rsync,
mirrored to princeton.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
as opposed to the current 3-level structure.
recent build system simplifications have enabled
this change, thus:
./build fw coreboot -> ./build roms
./build fw grub -> ./build grub
./build fw serprog -> ./build serprog
./update project release -> ./update release
./update project trees -> ./update trees
./update vendor download -> ./vendor download
./update vendor inject -> ./vendor inject
alper criticised that the commands were too long,
so i made them shorter!
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
i previously added this just for kicks, but it's not
actually needed; gnat isn't used on fam15h boards so
lbmk doesn't even use it (it's disabled).
in fact, i tested lbmk with crossgcc_ada handling
taken out, but with said patch; i still got build
errors with gnat anyway, on that old coreboot
revision (but gnat isn't needed there anymore).
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
We don't really need a custom coreboot tree for Chromebooks. I had added
one, because at a cursory glance to the available config/coreboot/board
subdirectories I had the impression that I should. But upstreams have
one tree for every board and I think we should move towards that too.
Move the one important BL31 makefile patch into the default coreboot
patches, update the gru boards' configs by running savedefconfig in the
cros tree and then running olddefconfig in the default tree.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
Riku's mSATA patch for HP8300USDT was merged upstream, so the
patch has been dropped from lbmk because it is contained within
this new coreboot revision.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
some users reported build errors. technically, there's
nothing wrong with lbmk but it relies on hostcc, and
hostcc is hit or miss when it comes to cross compiling
32-bit, depending on the build system of whatever project.
lbmk needs to handle cross compilation. for now, i'm just
disabling memtest86plus on non-64-bit hosts.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
in the future, we may start downloading files that aren't
blobs, such as mxm port configs (on mainboards that use
MXM graphics)
this directory will contain all of those files
generally change the language used, across lbmk, to make
use of "vendorfile" instead of "blob"
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
We don't have a directory names "srces", just "src".
Ditto ecs, mrcs <-- it's just ec and mrc
When referring to a file, e.g. blob/t1650/me.bin, that
makes much more sense, because it's a single blob, not
multiple blobs.
Don't pluralise what isn't plural
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
build/release/src was partly re-written to accomodate this
memtest86plus was patched to have a central Makefile, and
lbmk modified to use that, rather than mess with build32
and build64. the central Makefile just builds both targets
or cleans both targets
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
target.cfg can now specify e.g.
grub_timeout=20
this would then be inserted as timeout.cfg in cbfs,
containing the instruction:
set timeout=20
HP laptops need a bit of extra time, due to the delay
caused by the EC bug workaround deployed in GRUB
desktops in general need extra time. this too is set to
10s, like the HP laptops.
only insert timeout.cfg if actually needed (declared in
target.cfg), otherwise grub.cfg will default to 5s
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
now under coreboot mainboards, target.cfg can specify
a background. if not specified, the 1280x800 one is
assumed, and used by default. it can be overridden.
the path should be relative to:
config/grub/background/
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
