| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Currently seems to stall when booted from the GRUB
payload, but works when booted from the SeaBIOS menu.
I also tested it as a standalone payload and it seems
to boot. Will test on hardware next, and start adding
it to more mainboards.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
coreboot/dell7 is now part of coreboot/next, which in turn
has been updated, to accomodate 3050 micro patchset 18:
https://review.coreboot.org/c/coreboot/+/82053/18
It incorporates my Verb/VBT patches, which are therefore
no longer included separately.
Mate has fixed the USB config; see diff for details.
The configuration of USB ports was wrong, before.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
NOTE: Support added for xarch target x86_64-elf,
but U-Boot failed to build with this error:
OBJCOPY lib/efi_loader/helloworld.efi
x86_64-elf-objcopy: lib/efi_loader/helloworld_efi.so: invalid bfd target
make[2]: *** [scripts/Makefile.lib:476: lib/efi_loader/helloworld.efi] Error 1
Since I'm building U-Boot for x86_64 *on* an x86-64
host, and since that is currently the recommended type
of machine to use for lbmk development, and since the
other x86 payloads currently don't cross compile anyway,
this is an acceptable compromise for now. This is because
at present, I'm not making U-Boot the primary payload on x86,
instead preferring to chain it from GRUB and SeaBIOS.
The target.cfg file for x86 u-boot shows xarch/xtree commented.
Uncomment these to compile on crossgcc instead of hostcc.
I mention 64-bit because I initially did this first, but decided
to do 32-bit first. I'll work on the 64-bit one next (SPL).
It's only enabled in QEMU for now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
There were a lot of unnecessary patches, such as the VRAM
patches; as Nicholas Chin has explained to me, the drivers
for these machines will just allocate what RAM they want
anyway, so in a lot of cases the extra allocated Video RAM
simply reduces the total amount of memory for other uses.
In general, we have a lot of patches that have existed for
years. A much more aggressive sweep will be done in the next
major audit, especially when the revisions are updated again.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Thanks go to Nicholas Chin and Lorenzo Aloe for working on
and testing this code. Based on the 780 MT port.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
pin mod needed (soldering) but according to mate, you
can use some coffeelake CPUs on these machines, despite
them being intel 7th gen. this includes 8-core chips.
this patch enables the software configuration in coreboot.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Thanks go to Lorenzo Aloe and Nicholas Chin for working on
and testing this code.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
This is for blanking the ME region on release builds.
This is required for lbmk when doing Libreboot releases,
on images that use an Intel ME region.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Remove what is now unnecessary bloat, for ensuring that
GRUB is the primary payload; SeaGRUB is the only preference,
as per lbmk design.
The SeaBIOS hanging issue was fixed, so SeaGRUB is OK now.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
from nic3-14159/lbmk:mec5035-updates into master
Reviewed-on: https://codeberg.org/libreboot/lbmk/pulls/244
|
|
Again, I'm adapting the config to be as close to the
coreboot one as possible. I compiled directly from coreboot
earlier, and got SeaBIOS to work on my 3050.
I'm matching the setup as closely as possible. Once it works,
I can use that in a Libreboot release but then debug why the
old config wasn't working.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
I'm eliminating as many differences as possible between lbmk's
setup, and the setup that is default when simply building from
the gerrit patch, directly in coreboot, by just picking the
mainboard; in this way, coreboot picks SeaBIOS as payload. I
already changed the SeaBIOS configs, in the previous patch.
Upon testing, this seems to have fixed the SeaBIOS hanging. I
need to have both of these options selected, or SeaBIOS hangs
just after it says "Press ESC" for the boot menu.
With this config change, SeaBIOS does not hang; instead, it shows
the list of devices as normal, and boots your machine.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
- Update the MEC5035 S3 patches to the versions that were sent upstream
to prevent conflicts with subsequent patches for that EC.
- Update the patch that enables the S3 SMI handler in mainboard code so
that all Latitudes use the handler.
- Add a new patch that tells the EC to route power button events to the
host so that the OS can decide what to do. Without it, the EC powers
off the system without letting the OS cleanly shut down.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Specifically, use the same revision that Mate used in patchset 15.
This will ensure that any issues are *not* caused by the coreboot
revision; this is being done, because the old coreboot revision was
from July, but patchset 15 from Mate is based on a September revision
of coreboot.
I've been eliminating as many variables as possible, trying to fix
SeaBIOS payload on this machine, because it hangs in Libreboot, but
not when building from gerrit directly, which means the coreboot
revision may be a factor (since I'm using his patches on an older
revision so upstream might have made some changes since then that
the port relies on).
For this, a new coreboot tree is used, called "dell7", referring to
the fact that Kabylake is Intel's 7th generation.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Use patchset 15 instead of 14:
config/coreboot/default/patches/0061-WIP-OptiPlex-3050-Micro-port.patch
Rebase the verb patch; patchset 15 modified the Makefile:
config/coreboot/default/patches/0064-dell-optiplex_3050-add-hda_verb.c.patch
We were using patchset 14 for the 3050 micro:
https://review.coreboot.org/c/coreboot/+/82053/14
Now we use patchset 15:
https://review.coreboot.org/c/coreboot/+/82053/15
Without this patch, the fans are always on a low setting, on
the Dell OptiPlex 3050 Micro, even under stress conditions. With
this patch, the fans change speed according to CPU temperature.
I had to rebase my verb patch, because Mate modified the Makefile
to add his sch5555 handler, on the same line where I add hda_verb.
Mate tells me he will merge my verb and vbt patches into a further
patchset later on. For now, I've simply rebased these patches on
top of Mate's newer work; I've told him he can use them in his port.
I'm probably going to now issue a new revision ROM image for
Libreboot 20241008, so that users can get this fix sooner.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Thanks go to Nicholas Chin for helping me with this.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
on 3050micro, we disable seabios as a primary payload,
making grub a pribary payload instead.
the way it worked, the roms were still named seagrub
and the seabios rom would be compiled, but with the wrong
path, so seabios wouldn't be executed; seabios would hang
anyway, on this board.
instead, engineer it in such a way as to disable seabios_
images on this board. also, rename seagrub_ to grub_.
i normally only permit seagrub, and not grub, but i make an
exception for 3050micro because we know grub works, but seabios
currently hangs on this board (which means no bsd).
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
SeaBIOS is known to hang on this board. It is being investigated.
Add two variable options for target.cfg files:
* seabiosname
* grubname
This string defines where it would be located in CBFS.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
otherwise it takes ages to boot
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
SeaBIOS hangs without this. Thanks go to Mate Kukri who
suggested this workaround.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
This is using Mate Kukri's port, which was added in
previous lbmk revisions. I've added an IFD that sets
the HAP bit, and unlocks regions as standard.
vcfg is set to 3050micro, which defines downloading
of the MEv11 image and it will run deguard automatically.
I made a small adjustment to vendor.sh, because the hotpatch
logic for deguard uses -C in git, and when doing that, the
specified directory path is relative to that Git repository;
the .patch path has been adjusted accordingly.
Also add 3rdparty/fsp to coreboot/default modules.
This board requires the ifdtool option: -p sklkbl
The -p option tells flashrom what quirks are present in a
given IFD. We don't normally need this on other Libreboot
targets that we currently support. The -p option was needed
for creating this modified IFD, and it is therefore needed in
the inject script. Therefore, an "IFD_platform" option is
specified in a given board's target.cfg file. If this is set,
another variable is set that makes -p be used.
In this case, 3050's target.cfg says:
IFD_platform="sklkbl"
This option enables quirks for skylake/kabylake descriptors,
as required when using ifdtool.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Pretty much just copied the T1650 directory in config/,
then changed the board to 9010 SFF in menuconfig.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Add patches to convert the E6400 port into a GM45 Latitude variant and
add the E4300 as another variant, and create a config for the E4300.
Tested on my E6400 and E4300.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Dell OptiPlex 3050 Micro
I ran ./mk -u coreboot, to update existing configs
after merging. Actualy IFD and coreboot configs will
be done in the next revision. I've already added logic
for handling deguard, in preparation for this.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Commit 3ee4cc9ddec62276c374f8c7f0c0b3322cfaa9f6 (fix typo in dell
latitude coreboot coreboot config) fixed a typo from ${VARIANT_DIR) to
$(CONFIG_VARIANT_DIR). While this does work, since CONFIG_VARIANT_DIR is
a valid variable, it is not technically correct, as the default VBT path
set by coreboot's Kconfig files uses $(VARIANT_DIR), which is the same
as CONFIG_VARIANT_DIR, but with quotes stripped out.
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
see relevant patch added in the diff
set the clock on x4x boards to 96MHz like on GM45
fixes the following build error on x4x boards:
hw-gfx-gma-plls.adb:465:46: error: "INTEL_GMA_DPLL_REF_FREQ" not declared in "Config"
make: *** [Makefile:423: build/ramstage/libgfxinit/common/g45/hw-gfx-gma-plls.o] Error 1
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
some of my DDR2 checks were unnecessary, as nicholas pointed
out on irc, because they were in places that only ran if
DDR2 memory was used anyway.
in another, valid place, I was checking the wrong variable for
knowing what memory type is used.
this patch fixes build errors in lbmk:
src/northbridge/intel/gm45/raminit.c: In function 'dram_program_timings':
src/northbridge/intel/gm45/raminit.c:1120:29: error: 'sysinfo' undeclared (first use in this function); did you mean 'sysinfo_t'?
1120 | if (sysinfo->spd_type == DDR2)
| ^~~~~~~
| sysinfo_t
src/northbridge/intel/gm45/raminit.c:1120:29: note: each undeclared identifier is reported only once for each function it appears in
src/northbridge/intel/gm45/raminit.c: In function 'ddr2_odt_setup':
src/northbridge/intel/gm45/raminit.c:1291:21: error: 'sysinfo' undeclared (first use in this function); did you mean 'sysinfo_t'?
1291 | if (sysinfo->spd_type == DDR2) {
| ^~~~~~~
| sysinfo_t
make: *** [Makefile:423: build/romstage/northbridge/intel/gm45/raminit.o] Error 1
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
these configs were otherwise correct, but i typo'd a variable
in them when manually rebasing the old configs, after switching
to nicholas's new ports implemented as variants, where the old
ones in lbmk were individual board ports for those same boards.
Signed-off-by: Leah Rowe <info@minifree.org>
|
|
it is identical to fam15h_rdimm, with _udimm now removed;
the latter had a patch that added certain behaviour only
intended for rdimm, but the patch in question breaks various
configurations.
raminit has always been unreliable on these boards. i'd rather
simplify it all, in lbmk. i'll probably update this to the dasharo
tree later on, specificalyl for kgpe-d16
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
The libgfxinit patch and other patches e.g. DDR2 fix, are
now provided in coreboot/default. The Latitude E6400 is now
using the newer coreboot revision from late July 2024.
Some other configs had to change because of this, relating to
the new way that Nicholas handles timing on LVDS displays
with the E6400 port; a default 96MHz clock is still used for
pixel reference clock, overridden with a value of 100MHz on
other GM45 machines, where 96MHz was previously hardcoded.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Several patches are now merged upstream and no longer needed
in lbmk, such as the HP EliteBook 8560w patch, and related
patches. Some patches were changed, for example the Dell Latitude
ivb/snb laptops are now variants in coreboot, instead of being
individual ports; now they re-use the same base code.
This this, the corresponding files under config/submodules
have changed, for things like 3rdparty submodules e.g. libgfxinit,
and tarballs e.g. crossgcc.
This is long overdue, and will enable more boards to be added.
This newer revision will be used in the next release, and some
follow-up patches will merge these trees into default:
* coreboot/haswell
* coreboot/dell
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
set a default one in mkhelper.cfg
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Never, ever build images where GRUB is the primary payload.
These options have been removed from target.cfg handling:
* seabios_withgrub
* grub_withseabios
The "payload_grub" variable now does the same thing as
the old "seabios_withgrub" variable, if set.
The "grubonly" configuration is retained, and enabled by
default when SeaGRUB is enabled (non-grubonly also available).
Due to lbmk issue #216, it is no longer Libreboot policy to
make GRUB the primary payload on any board. GRUB's sheer size
and complexity, plus the large number of memory corruption issues
similar to it that *have* been fixed over the years, tells me
that GRUB is a liability when it is the primary payload.
SeaBIOS is a much safer payload to run as primary, on x86, due
to its smaller size and much more conservative development; it
is simply far less likely to break.
If GRUB breaks in the future, the user's machine is not
bricked. This is because SeaBIOS is the default payload.
Since I no longer wish to ever provide GRUB as a primary
payload, supporting it in lbmk adds needless bloat that
will later probably break anyway due to lack of testing,
so let's just assume SeaGRUB in all cases where the user
wants to use a GRUB payload.
You can mitigate potential security issues with SeaBIOS
by disabling option ROM execution, which can be done at
runtime by inserting integers into CBFS. The SeaBIOS
documentation says how to do this.
Libreboot's GRUB hardening guide still says how to add
a bootorder file in CBFS, making SeaBIOS only load GRUB
from CBFS, and nothing else. This, combined with the
disablement of option ROM execution (if using Intel
graphics), pretty much provides the same security benefits
as GRUB-as-primary, for example when setting a GRUB password
and GPG checks, with encrypted /boot as in the hardening guide.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
replace it with logic that simply uses "." to load
files directly. for this, "vcfg" is added as a variable
in coreboot target.cfg files, referring to a directory
in config/vendor/ containing a file named pkg.cfg, and
this file then contains the same variables as the
erstwhile config/vendor/sources
config/git files are now directories, also containing
pkg.cfg files each with the same variables as before,
such as repository link and commit hash
this change results in a noticeable reduction in code
complexity within the build system.
unified reading of config files: new function setcfg()
added to lib.sh
setcfg checks if a config exists. if a 2nd argument is
passed, it is used as a return value for eval, otherwise
a string calling err is passed. setcfg output is passed
through eval, to set strings based on config; eval must
be used, so that the variables are set within the same
scope, otherwise they'd be set within setcfg which could
lead to some whacky results.
there's still a bit more more to do, but this single change
results in a substantial reduction in code complexity.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
this is bloat, because it's something the user can already
do at runtime configuration anyway.
set it to a reasonable default of 8 seconds instead of 5,
and don't honour the timeout variable in target.cfg.
this will be documented in the next release.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the background is only a few kb. the whole rationale
before was to limit the space used in memdisk, but this
decision was made when the background was much bigger;
it has since been optimised greatly, and the grub modules
were heavily reduce, so it should be safe.
grub's memdisk breaks when you add too much data to it.
as part of simplifying the rest of lbmk, this change removes
some more bloat from the rest of lbmk. handling this in the
memdisk is much simpler than handling it with cbfstool.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
fixes DP++ and adds a DP that wasn't even there before,
on all currently supported variants of these machines
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
the patch fixes IGD on certain xeon processors
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
remove nvme support from the "default" grub tree
now there are three trees:
* default: no xhci or nvme patches
* nvme: contains nvme support
* xhci: contains xhci and nvme support
this is in case a bug like lbmk issue #216 ever occurs
again, as referenced before during lbmk audit 5
there is no indication that the nvme patch causes any
issues, but after previous experience i want to be sure
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
certain code checks for build.list, to skip it, for
example in items()
we already use config/data/grub to store grub config data
that applied to all trees
create these directories too:
config/data/coreboot
config/data/u-boot
config/data/seabios
move the respective build.list files in here, and also
to config/data/grub
now multi-tree projects contain, per directory, just the
target.cfg file and the patches directory. this is much
cleaner, because some of the logic can be simplified more
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
|
Re-add xHCI only on haswell and broadwell machines, where
they are needed. Otherwise, keep the same GRUB code.
The xHCI patches were removed because they caused issues
on Sandybridge-based Dell Latitude laptops. See:
https://codeberg.org/libreboot/lbmk/issues/216
The issue was not reported elsewhere, including on the
Haswell/Broadwell hardware where they are needed, but the
build system could only build one version of GRUB.
The older machines do not need xHCI patches, because they
either do not have xHCI patches, or work (in GRUB) because
they're in EHCI mode when running the payload.
So, the problem is that we need the xHCI patches for GRUB
on Haswell/Broadwell hardware, but the patches break
Sandybridge hardware, and we only had the one build of GRUB.
To mitigate this problem, the build system now supports
building multiple revisions of GRUB, with different patches,
and each given coreboot target can say which GRUB tree to use
by setting this in target.cfg:
grubtree="xhci"
In the above example, the "xhci" tree would be used. Some
generic GRUB config has been moved to config/data/grub/
and config/grub/ now looks like config/coreboot/ - also,
the grub.cfg file (named "payload" in each tree) is copied
to the GRUB source tree as ".config", then added to GRUB's
memdisk in the same way, as grub.cfg.
Several other design changes had to be made because of this:
* grub.cfg in memdisk no longer automatically jumps to one
in CBFS, but now shows a menuentry for it if available
* Certain commands in script/trees are disabled for GRUB,
such as *config make commands.
* gnulib is now defined in config/submodule/grub/, instead
of config/git/grub - and this mitigates an existing bug
where downloading gnulib first would make grub no longer
possible to download in lbmk.
The coreboot option CONFIG_FINALIZE_USB_ROUTE_XHCI has been
re-enabled on: Dell OptiPlex 9020 MT, Dell OptiPlex 9020 SFF,
Lenovo ThinkPad T440p and Lenovo ThinkPad W541 - now USB should
work again in GRUB.
The GRUB payload has been re-enabled on HP EliteBook 820 G2.
This change will enable per-board GRUB optimisation in the
future. For example, we hardcode what partitions and LVMs
GRUB scans because * is slow on ICH7-based machines, due
to GRUB's design. On other machines, * is reasonably fast,
for automatically enumerating the list of devices for boot.
Use of * (and other wildcards) could enable our GRUB payload
to automatically boot more distros, with minimal fuss. This
can be done at a later date, in subsequent revisions.
Signed-off-by: Leah Rowe <leah@libreboot.org>
|
