util/e6400-flash-unlock: Rename to dell-flash-unlock

This more accurately describes the scope of the utility.

Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>

1 files changed, 0 insertions, 217 deletions

diff --git a/util/e6400-flash-unlock/e6400_flash_unlock.c b/util/e6400-flash-unlock/e6400_flash_unlock.c
deleted file mode 100644
index 174a1c92..00000000
--- a/util/e6400-flash-unlock/e6400_flash_unlock.c
+++ /dev/null
@@ -1,217 +0,0 @@
-/* SPDX-License-Identifier: MIT */
-/* SPDX-FileCopyrightText: 2023 Nicholas Chin */
-
-#include <sys/mman.h>
-
-#include <err.h>
-#include <errno.h>
-#include <fcntl.h>
-#include <stdint.h>
-#include <stdio.h>
-#include <stdlib.h>
-#include <unistd.h>
-
-#include "accessors.h"
-
-int get_fdo_status(void);
-int check_lpc_decode(void);
-void ec_set_fdo();
-void write_ec_reg(uint8_t index, uint8_t data);
-void send_ec_cmd(uint8_t cmd);
-int wait_ec(void);
-int check_bios_write_en(void);
-int set_gbl_smi_en(int enable);
-int get_gbl_smi_en(void);
-
-#define EC_INDEX 0x910
-#define EC_DATA 0x911
-#define EC_ENABLE_FDO 2
-
-#define LPC_DEV PCI_DEV(0, 0x1f, 0)
-
-#define RCBA_MMIO_LEN 0x4000
-
-/* Register offsets */
-#define SPIBAR 0x3800
-#define HSFS_REG  0x04
-#define SMI_EN_REG 0x30
-
-volatile uint8_t *rcba_mmio;
-uint16_t pmbase;
-
-int
-main(int argc, char *argv[])
-{
-	int devmemfd;
-	(void)argc;
-	(void)argv;
-
-	if (sys_iopl(3) == -1)
-		err(errno, "Could not access IO ports");
-	if ((devmemfd = open("/dev/mem", O_RDONLY)) == -1)
-		err(errno, "/dev/mem");
-
-	/* Read RCBA and PMBASE from the LPC config registers */
-	long int rcba = pci_read_32(LPC_DEV, 0xf0) & 0xffffc000;
-	pmbase = pci_read_32(LPC_DEV, 0x40) & 0xff80;
-
-	/* FDO pin-strap status bit is in RCBA mmio space */
-	rcba_mmio = mmap(0, RCBA_MMIO_LEN, PROT_READ, MAP_SHARED, devmemfd,
-			rcba);
-	if (rcba_mmio == MAP_FAILED)
-		err(errno, "Could not map RCBA");
-
-	if (get_fdo_status() == 1) { /* Descriptor not overridden */
-		if (check_lpc_decode() == -1)
-			err(errno = ECANCELED, "Can't forward I/O to LPC");
-
-		printf("Sending FDO override command to EC:\n");
-		ec_set_fdo();
-		printf("Flash Descriptor Override enabled.\n"
-			"Shut down (don't reboot) now.\n\n"
-			"The EC may auto-boot on some systems; if not then "
-			"manually power on.\n When the system boots rerun "
-			"this utility to finish unlocking.\n");
-	} else if (check_bios_write_en() == 0) {
-		/* SMI locks in place, try disabling SMIs to bypass them */
-		if (set_gbl_smi_en(0)) {
-			printf("SMIs disabled. Internal flashing should work "
-				"now.\n After flashing, re-run this utility "
-				"to enable SMIs.\n (shutdown is buggy when "
-				"SMIs are disabled)\n");
-		} else {
-			err(errno = ECANCELED, "Could not disable SMIs!");
-		}
-	} else { /* SMI locks not in place or bypassed */
-		if (get_gbl_smi_en()) {
-			/* SMIs are still enabled, assume this is an Exx10
-			 * or newer which don't need the SMM bypass */
-			printf("Flash is unlocked.\n"
-				"Internal flashing should work.\n");
-		} else {
-			/* SMIs disabled, assume this is an Exx00 after
-			 * unlocking and flashing */
-			set_gbl_smi_en(1);
-			printf("SMIs enabled.\n"
-				"You can now shutdown the system.\n");
-		}
-	}
-	return errno;
-}
-
-int
-get_fdo_status(void)
-{
-	return (*(uint16_t*)(rcba_mmio + SPIBAR + HSFS_REG) >> 13) & 1;
-}
-
-int
-check_lpc_decode(void)
-{
-	/* Check that at a Generic Decode Range Register is set up to
-	 * forward I/O ports 0x910 and 0x911 over LPC for the EC */
-	int i = 0;
-	int gen_dec_free = -1;
-	for (; i < 4; i++) {
-		uint32_t reg_val = pci_read_32(LPC_DEV, 0x84 + 4*i);
-		uint16_t base_addr = reg_val & 0xfffc;
-		uint16_t mask = ((reg_val >> 16) & 0xfffc) | 0x3;
-
-		/* Bit 0 is the enable for each decode range. If disabled, note
-		 * this register as available to add our own range decode */
-		if ((reg_val & 1) == 0)
-			gen_dec_free = i;
-
-		/* Check if the current range register matches port 0x910.
-		 * 0x911 doesn't need to be checked as the LPC bridge only
-		 * decodes at the dword level, and thus a check is redundant */
-		if ((0x910 & ~mask) == base_addr) {
-			return 0;
-		}
-	}
-
-	/* No matching range found, try setting a range in a free register */
-	if (gen_dec_free != -1) {
-		/* Set up an I/O decode range from 0x910-0x913 */
-		pci_write_32(LPC_DEV, 0x84 + 4 * gen_dec_free, 0x911);
-		return 0;
-	} else {
-		return -1;
-	}
-}
-
-void
-ec_set_fdo()
-{
-	/* EC FDO command arguments for reference:
-	 * 0 = Query EC FDO status
-	 * 2 = Enable FDO for next boot
-	 * 3 = Disable FDO for next boot */
-	write_ec_reg(0x12, EC_ENABLE_FDO);
-	send_ec_cmd(0xb8);
-}
-
-void
-write_ec_reg(uint8_t index, uint8_t data)
-{
-	sys_outb(EC_INDEX, index);
-	sys_outb(EC_DATA, data);
-}
-
-void
-send_ec_cmd(uint8_t cmd)
-{
-	sys_outb(EC_INDEX, 0);
-	sys_outb(EC_DATA, cmd);
-	if (wait_ec() == -1)
-		err(errno = ECANCELED, "Timeout while waiting for EC!");
-}
-
-int
-wait_ec(void)
-{
-	uint8_t busy;
-	int timeout = 1000;
-	do {
-		sys_outb(EC_INDEX, 0);
-		busy = sys_inb(EC_DATA);
-		timeout--;
-		usleep(1000);
-	} while (busy && timeout > 0);
-	return timeout > 0 ? 0 : -1;
-}
-
-int
-check_bios_write_en(void)
-{
-	uint8_t bios_cntl = pci_read_32(LPC_DEV, 0xdc) & 0xff;
-	/* Bit 5 = SMM BIOS Write Protect Disable (SMM_BWP)
-	 * Bit 1 = BIOS Lock Enable (BLE)
-	 * If both are 0, then there's no write protection */
-	if ((bios_cntl & 0x22) == 0)
-		return 1;
-
-	/* SMM protection is enabled, but try enabling writes
-	 * anyway in case the vendor SMM code doesn't reset it */
-	pci_write_32(LPC_DEV, 0xdc, bios_cntl | 0x1);
-	return pci_read_32(LPC_DEV, 0xdc) & 0x1;
-}
-
-int
-set_gbl_smi_en(int enable)
-{
-	uint32_t smi_en = sys_inl(pmbase + SMI_EN_REG);
-	if (enable) {
-		smi_en |= 1;
-	} else {
-		smi_en &= ~1;
-	}
-	sys_outl(pmbase + SMI_EN_REG, smi_en);
-	return (get_gbl_smi_en() == enable);
-}
-
-int
-get_gbl_smi_en(void)
-{
-	return sys_inl(pmbase + SMI_EN_REG) & 1;
-}