We need to initialize the USB subsystem before we can use USB devices
like keyboards and external disks, by running `usb start`. Use the
PREBOOT config option to run the necessary command before U-Boot tries
to automatically boot anything. It's already enabled for boards other
than gru_kevin and gru_bob, so just update those two configs.

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>

Set default U-Boot revision to v2024.10 and rebase patches on top of
that. The video subsystem now has switched to using the 'cyclic'
mechanism, so the code around one of the video patches changed a bit.

x86 boards were already switched to v2024.10. Update U-Boot for the
remaining ARM64 boards as usual:

- Turn old configs into defconfigs (./update trees -s u-boot)
- Save the diff from old upstream defconfig (diffconfig $theirs $ours)
- Update U-Boot revision, rebase patches, and clean old trees
- Prepare new U-Boot tree (./update trees -f u-boot)
- Review the diffconfigs to see if any options were renamed upstream
- Copy over the new upstream defconfigs and apply earlier diff
- Turn new defconfigs into configs (./update trees -l u-boot)

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>

This is a patch from Simon Glass. U-Boot clears the display
when it starts up, but was asking the VESA driver to do the
same, needlessly; this patch avoids the latter.

A further patch is also included, which provides a better
message when jumping into long mode on the SPL (64-bit) target,
dumping it on the serial console instead of using printf.

Signed-off-by: Leah Rowe <leah@libreboot.org>

U-Boot was hanging on hardware, but not Qemu. This is because on
the machines tested, namely the X200 and E6230 laptops supported
in Libreboot, the UART was disabled from coreboot.

This U-Boot patch from Simon Glass works around the issue by
silently disabling the UART when it isn't there. Instead,
output is sent to the display and U-Boot no longer hangs.

Signed-off-by: Leah Rowe <leah@libreboot.org>

It's a new experimental payload in Libreboot, so we may aswell
start with the very latest release of U-Boot.

Signed-off-by: Leah Rowe <leah@libreboot.org>

Currently seems to stall when booted from the GRUB
payload, but works when booted from the SeaBIOS menu.

I also tested it as a standalone payload and it seems
to boot. Will test on hardware next, and start adding
it to more mainboards.

Signed-off-by: Leah Rowe <leah@libreboot.org>

NOTE: Support added for xarch target x86_64-elf,
but U-Boot failed to build with this error:

OBJCOPY lib/efi_loader/helloworld.efi
x86_64-elf-objcopy: lib/efi_loader/helloworld_efi.so: invalid bfd target
make[2]: *** [scripts/Makefile.lib:476: lib/efi_loader/helloworld.efi] Error 1

Since I'm building U-Boot for x86_64 *on* an x86-64
host, and since that is currently the recommended type
of machine to use for lbmk development, and since the
other x86 payloads currently don't cross compile anyway,
this is an acceptable compromise for now. This is because
at present, I'm not making U-Boot the primary payload on x86,
instead preferring to chain it from GRUB and SeaBIOS.

The target.cfg file for x86 u-boot shows xarch/xtree commented.
Uncomment these to compile on crossgcc instead of hostcc.

I mention 64-bit because I initially did this first, but decided
to do 32-bit first. I'll work on the 64-bit one next (SPL).

It's only enabled in QEMU for now.

Signed-off-by: Leah Rowe <leah@libreboot.org>

U-Boot has migrated to using upstream device-tree files for gru boards,
but the clock driver doesn't yet support setting rates for a certain
clock that upstream uses for the eDP display. It happens to work without
it, so for now remove the clock setting until the driver is fixed.

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>

Commit 46e01c0e1dad ("u-boot: Avoid building U-Boot-only binman images")
added a patch that prevents an error while building U-Boot, due to some
U-Boot images needing a copy of BL31 that we are not passing in.

Removing build instructions for these images isn't really necessary,
when we can instead tell the build tool that it shouldn't exit with an
error. It checks a BINMAN_ALLOW_MISSING environment variable for this,
but just unconditionally replace the check with the argument.

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>

Set default U-Boot revision to v2024.07 and rebase patches on top of
that. One patch that fixes drawing box characters (UTF-8 to CP437) had
an alternative merged, another hack we have to fix regulator issues is
no longer neccessary as the issue is fixed, and my QEMU patches were
merged upstream, so drop these patches. One patch we have to disable
binman images can be replaced by a simpler alternative so drop it too.

Upstream kconfig status is still unstable, so updating configs with
`make oldconfig` would miss important upstream changes, since they rely
on carrying defaults via upstream defconfigs. Update the configs as
such, like before:

- Turn old configs into defconfigs (./update trees -s u-boot)
- Save the diff from old upstream defconfig (diffconfig $theirs $ours)
- Update U-Boot revision, rebase patches, and clean old trees
- Prepare new U-Boot tree (./update trees -f u-boot)
- Review the diffconfigs to see if any options were renamed upstream
- Copy over the new upstream defconfigs and apply earlier diff
- Turn new defconfigs into configs (./update trees -l u-boot)

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>